Quantcast
Jump to content


1999 Kawasaki Mule 2510 4x4

ChrisL

By ChrisL
in Kawasaki UTV SxS Forum

 Share

Recommended Posts

ChrisL Newbie

ChrisL

Posted
Posted

I recently obtained a 1999 Kawasaki Mule 2510 4x4. While working on, I noticed the rear hub brake grease/dust seals were not there. I ordered and received but have no idea of the installation orientation. Has anyone tackled this or have a sketch/ picture that could help?

Travis Grand Master

Travis

Posted
Posted

It looks like It just fits around the brake panel, and then the drum fits over it. I wonder why it has that seal around it? Mine (Even though it's a 550) doesn't have them.

Manuals are a must have for working on equipment, and will likely have every answer to your questions https://www.ebay.com/itm/KAWASAKI-MULE-2510-UTILITY-VEHICLE-ATV-SERVICE-MANUAL-DIESEL-ENGINE/264515499459?hash=item3d965a35c3:g:7XcAAOSwJwFduPo8&redirect=mobile

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • SkyPilot56
      working on a coleman 550 out fitter
      By SkyPilot56
      working on a coleman 550 out fitter , had a shit load of codes, coil, injector , and the map sensor for fuel injector replaced all 3 and figured it would start , but no joy have spark (new plug also and inline fuel filter) cleared the codes and still have the engine light , turns over fine but damn thing still will not start, friends daughters were driving it and turned it off to park , and went back to start it and same thing turns over but will not start , with this machine anyone have any ideas as to what the hell , I should be looking for , no plug's unplug checked wires none seem to be pulled apart or broken !
    • A P
      2022 Hisun Sector 550 eps. Power steering not working
      By A P
      Hi
      I have a 2022 hisun sector eps 550. 30amp fuse is blown for eps. Checked the motor and it’s fine. Opened up the controller and found a bad diode. Dealer wanted 500$ for the controller. Just posting this in case it helps someone. I couldn’t read numbers from the old one so just took a guess and replaced it with a 100v 3amp diode. 
    • clint501
      Hisun E1 charger not working
      By clint501
      I recently purchased a Hisun E1 and the other day the charger stopped working properly. The LED on the dash blinks red & green and the light on the side of the charger also blinks red & green. The fan on the charger does not come on like it used to do. There is no error code that I can see. Does anyone have any suggestions to remedy this?
    • rsar
      Washing Mule Underbody
      By rsar
      Hey guys. I was wondering if anyone pressure washes their Mule underbody. Three years in, I have yet to do this. I'm worried that the pressure washer could damage or dislodge something but it's gotten to the point that it could use a bath. Any thoughts?
    • D MAYNARD
      Axis 500 4x4 turns over but no spark
      By D MAYNARD
      I have an Axis 500 4x4 UTV that I was given.  It looks like an almost new machine with 39 hrs on it however it was apparently under water from the hurricane . I have no spark at the plug. I have replaced the plug, the plug wire, & the stator so far. Can anyone advise me of what i need to check and or replace to get this thing running? Any advise would be greatly appreciated. 
                                    Thank You,
                                  D Maynard 
       

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...