Quantcast
Jump to content


Recommended Posts

Posted

Does anyone know why the middle of my front tires are wearing too fast?  I just checked the pressures, and they were at 24psi.  The manual says 10psi. Could that be the reason, but why aren't the rear tires showing excessive wear?  I've attached photos.

Any suggestions would be appreciated.

John

 

20250704_1330401.thumb.jpg.73ebc502075592e90a27f9955a5b2c12.jpg

20250704_132704[2].jpg

20250704_132713[1].jpg

20250704_132741[1].jpg

Posted

You've answered your own question. The pressure is way too high. It's only running on that portion of the tire and the fronts wear faster than the rears because they take a beating from steering, especially on hard pavement. You must also have a very hard ride. Get the pressure down to the recommended level.

  • Like 1
Posted

Yup, as been mentioned it's way too high. They're pretty stiff sidewalls so you can get away with the lower psi. I think I only use around 6 or 8 psi in my Landmaster and seem to be wearing ok.

Be aware tho that most tire manufacturers state the max weight when stating the air pressure. For example, in a car you have passengers in all the seats and a full trunk. Most people don't drive year round like that. Unless I'm doing heavy work I rarely have the max pressure even in my tractors.

 The low profile tires on cars are a bit more finicky tho, just have to experiment.

Posted
1 hour ago, Jaygyver said:

Yup, as been mentioned it's way too high. They're pretty stiff sidewalls so you can get away with the lower psi. I think I only use around 6 or 8 psi in my Landmaster and seem to be wearing ok.

Be aware tho that most tire manufacturers state the max weight when stating the air pressure. For example, in a car you have passengers in all the seats and a full trunk. Most people don't drive year round like that. Unless I'm doing heavy work I rarely have the max pressure even in my tractors.

 The low profile tires on cars are a bit more finicky tho, just have to experiment.

I'd be careful though on going too low with car tires. At long highway/interstate speeds low pressure can cause the tire to overheat and have a blowout. Extreme case but it does happen. Same with too high pressure but because higher temp at speed causes higher pressure, even worse on hotter days.

Posted

Well that goes with common sense too I guess. In a Hiway vehicle yeah, 5 or 10 psi below the maximum is usually  more than enough. But then again, if you load it up for a trip across the country you should definitely raise the air up a bit. In general air it up for the usage you're driving most of the time and the tire wear should be good. I used to drive quite a few miles so I kept an eye on the wear. With my PU and trailer when loaded I did find that it handled much better at the max rated psi.

 Off road smaller UTV and the like usually the tires have a much stiffer sidewall anyway and it's not like you'll be doing 70+ MPH with it for hours on end.

  • Like 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By rdc
      I posted this before , but I had the year wrong. The part I need is for a 2014, I don't know what all years will work, but I need the 2 bearing style with the spacer in the middle. It looks like this pic. If anyone has one I'll buy it rite away. my email is [email protected]. Thanks, RC

    • By rdc
      Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]
    • By paul allen
      right front axle cv joint boot keeps getting torn up from the inside out....the stock one was damaged from a stick...i have replaced  the axle 4 times with aftermarket axles that fit fine..after 4-5 miles of riding even on grass.the outer boot get torn up from the inside out...all 4 brand new alxes...bearings are fine nothing bent everything fits just fine....nothing seems to be binding.....any thoughts?????
       
       
      thanks...pa
       
    • By Jamie 67
      Why is there 2 different length keys for my tboss 1000?
    • By Sidewinder
      All mid 2008 through 2014 Polaris RZR 800 series have a big problem with the rear differential pinion nut backing off, allowing the pinion gear to shoot into the rear differential, destroying the rear differential. This has happened with machines with as little as less than 100 miles on them! Reports indicate that there are no problems, nor warnings, until the rear differential grenades, locking the rear axles solid! This requires the machine to be lifted onto a trailer, to be transported for rear differential replacement, as it destroys the case. After failure, rear differential replacement can be quite expensive: labor alone can run from $800-$1200 and a new OEM Spicer rear diff, if you can find one, can run from $1700-$2500! So, if you own any Polaris RZR 800 series between the years of 2008-2014, I recommend that you do this repair before further use of your machine. personally, I have grounded my machine until it can be done. Please check the online post for your own awareness.

×
×
  • Create New...