Quantcast
Jump to content

2010 Hisun 700 - wont idle and running rough


William

Recommended Posts

Hello all 

I have a 2010 hisun 700 carb model, it was running great all spring during covid then all of a sudden it started stalling at low RPMs and now wont idle at all.  It will run if i keep my foot on the gas but its just doesn't sound right so I stopped running it. 

My first thought was bad fuel, we had a lot of rain this spring and thought maybe condensation so i drained the tank, changed all the filters and even got new gas line and removed the second tank just to be safe after reading about not need it, still nothing.

Cleaned the carb and still nothing

Bought a new carb just to be safe as they are cheap enough and still running rough

Found the other issue with the Second Air Supply and a hose that comes from the exhaust that was broken, bought a new one of those and tried to attach it and it disintegrated in my hands when i touched it so i tried to attach it to the 1/2 that was left just trying to see if it would complete the vacuum but still ran rough

Changed the oil and filter too just in case it was that but still nothing

Took the new carb apart and cleaned it just to be safe, took out the air/fuel cover which is the stupidest thing when they send it to you without a screw driver to take the cover off so drilled it until a screwdriver could unscrew it - turned it all the way in then backed it out 2 full turns (like everyone says is the starting point) and it ran worse.

Bought a new coil just in case the spark was the issue, installed that and getting good spark so not that.

Bought a new air filter and have to still put that in so will try that tomorrow

Anything I missing, I have tried all i know and there is not enough youtube videos on repairs on these carts so looking for you folks to see if you can assist and give me some guidance on this issue

Thanks!!

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Randyh79
      Is there a way to adjust the brightness of the dash light on aHisun 750 sector?
    • By todd93
      Hi, all! I. I'm new to the board, hoping someone could help me out! I have a 2020 Hisun Sector 550C that I bought new in 2021. Today, I took some stuff next door to my parents. When I went to leave, I turned on the key, heard the solenoid click, but no lights, no guage activity, no fuel pump, and no starter. 
       
      The battery is good, I checked all the fuses, they are good. Not sure if the relays are good, or even what to look for there. Is it possible that it's maybe a wire? 
      I'm really stumped on this one! Any help would be deeply appreciated! Attached is a pic of the fuse box layout. 
       
      Thanks! 
      Todd 
    • By donwan
      View File 2017 Hisun Strike 900 Service Manual
      Here's the service manual for the 2017 hisun strike 900.
      Submitter donwan Submitted 05/29/2024 Category Hisun  
    • By Buddee
      Put a new carb on the 500 to replace the leaking OE one.  Machine idles fine and mid and top end runs great.  It tends to have a hesitation right from the start - bottom end.   Thinking it may be the air/fuel screw??  I didn't do anything with the carb out of the box and is it direct replacement for my machine.  Of interest is the manual choke doesn't seem to work very good now.... wonder is it getting too much air?
       
      Any help appreciated!
       
       
    • By JimS409
      I picked up this Hisun 700cc for a good deal. no crank no start unit 1900 miles on it. Put a new battery and starter solenoid fired right up but sounded rough some kind of rattle/clunk noise.  Does anyone know what this noise could be? Couldn't get a better video of it running as i don't want to risk doing more damage. Drained the oil it looks good no metal in it. 

      445374820_7315077208620291_6073155782020130975_n.mp4  
×
×
  • Create New...