Quantcast
Jump to content


2009 Joyner Trooper 1100 T2 diff cable removal

Anthony Butler

By Anthony Butler
in Joyner UTV SxS Forum

 Share

Recommended Posts

Dan B Community Regular

Dan B

Posted
Posted

I looked at my rear differential.  It looks like I'd have to remove the differential to get access to the internal cable connection which means I'd have to just about remove all the rear axle components. Before doing that, eliminate all other possibilities such as a binding lever (I presume you did that).  Also, get under your ride to see of there's something as simple as a clamp.  It would be a poor design if I have to remove and disassemble a differential just to preplace the cable.  Maybe someone has a service manual that give a better answer than I have.

Does your 4WD lever "lock" into the 4WD position or is it soft and mushy like mine?

mixfixdave Enthusiast

mixfixdave

Posted
Posted

I’m thinking if the locker pin is pulled into the diff enough that you can’t get the cable out, then you need to remove the diff and open it up.
Happened to me once, locker wouldn’t engage, but the problem was the locker mechanism/fork inside the differential was bent and off the locker ring. I straightened it and it’s been fine for years.
Also had some loose ring gear bolts and did the Lenny upgrade while I had it apart.
Here’s a pic of the locker fork and ring
b79d67cf34cda34a682225906dc649a3.jpg

  • 1 year later...
jetndude Newbie

jetndude

Posted
Posted

Thanks for that pic. I just ordered a new rear diff and it came with a (damaged in shipping) broken diff lock actuator lever (that connects to the cable going to the front). I wanted to know if that pin was removable somehow and you just showed me what's on the other side ... doesn't look removable. Thanks a bunch!

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Similar Topics

    • rdc
      Joyner 1100 oil pressure problem.
      By rdc
      I have a 2007 Joyner 1100 sand viper and  before it even get's to where the thermostat opens up the oil pressure get's so low I have to shut it down. What could fix this ? I thought about adding an oil cooler with fan, thicker oil, or removing the thermostat. Any advice?
    • mrpro
      Coleman UT400 rear shock height adjustment
      By mrpro
      I got the fronts adjusted.  I'm trying to raise the ride height in the rear, but my spanner wrench keeps slipping.  Is there an easier better way?  It's like there's too much pressure working against me to be able to twist the height adjusters.  How can I relieve that tension to make them easier to turn?  
    • jertex
      Shift cable problem, 2017 Stampede 900, need advice
      By jertex
      I bought a 2017 Stampede 900 last fall that was new, old stock with less than 5 hours on it thinking that I would be getting a relatively trouble free UTV as compared to buying a used Polaris or CanAm, or Honda, etc. It's been a little quirky, but reliable. What I thought was just a minor issue with this model, the difficulty in shifting between R, N, L, H, etc., was just a characteristic of this model is now a big problem. I had to climb two very steep trails to get to the upper meadow of our hunting property, which seemed to stress the UTV more than usual since I was carrying some lumber to work on a platform for a hunting blind, and when I went to shift into park, I felt something give and it would not shift out of low, but it did move up into high gear.  I couldn't get it to shift at all at that point and the shifter felt mushy for lack of a better word. I was able to get it down to the lodge and when I investigated, I discovered that the straight, metal tube portion of the shift cable had bent to almost 90 degrees (see pics). I'm positive that it had already had some deformation that had happened previously and it had the right amount of resistance to bend to the point where it was unusable. 
      I have two questions:
      1. I suspect that there must be some other issues that makes this UTV difficult to shift, and I'm wondering if this is a common problem and if someone could enlighten me on what could cause this to be difficult to shift?
      2. Have any of you had this happen and if so, how difficult is it to replace the shifter cable?
      Any other advice is welcome, this is the first UTV that I've ever owned, so I don't know much about working on these or maintaining them. I'm relatively capable when it comes to working on my own vehicles in general, and I'm not afraid to take things apart and get my hands dirty.
      Thanks in advance for any insight, I'll be traveling most the day so I won't get a chance to look at replies until this evening.


       
    • rdc
      Looking for the left side shaft carrier where the rear bearings go for a 2014 1100cc sand viper, I understand an 800 cc carrier will also work.
      By rdc
      I posted this before , but I had the year wrong. The part I need is for a 2014, I don't know what all years will work, but I need the 2 bearing style with the spacer in the middle. It looks like this pic. If anyone has one I'll buy it rite away. my email is [email protected]. Thanks, RC

    • rdc
      Looking for a left rear shaft carrier (just the carrier) for a 2007 Joyner 1100 sand viper
      By rdc
      Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...