Quantcast
Jump to content


Recommended Posts

Posted

Ok so I can’t get an adapter for my two cheap code readers?

im assuming an adapter that is 4 pins and fits the plug in next to the fuse box may work. IMG_0277.thumb.jpeg.482378155c5d523a6e223d450cccaa5b.jpegBut if it can’t read the code from the Delphi based deal you described then it would be useless. I think it’s some kind of motorcycle brand based adapter like Yamaha or Harley. It’s just a cheap enough solution that I may try it before I spend 300$. Maybe you already know what you’re talking about. I sure don’t know much in this & many other areas. If I did my UTV would be running and not such a terrible disappointment 

Posted

Can someone tell me what connector plug you need to get to connect my Tiny Scan to connect it to my Hisun HS-550 Performance made for Rural King? The folks at that make and sell the Tiny Scan said it will work on the Hisun with Delphi EFI system. Hisun said the port connection should be under the bench seat although I have yet to find it. He said it is a white connector with black cap that will have to be removed to plug in the code scan tool and I think he said it was a 6 pin plug.

Posted

Not sure if this will help, as here are posts for the UT400, but lately with all the advertising on this blog, I find it hard to read anything anymore. I found the plug on mine under the seat,

Try here:

 

Posted

I just got off the phone with the company that makes the TINY SCAN 301 and the TINY SCAN TS-140 the TS-140 is the one I have he told me both come with a plug on them that will plug into the Hisun UTV  although I have heard the newer HISUN's use OBD2 if you have a UTV like my 2018 HISUN HS-550 Performance made for Rural King by HISUN Motor Company in Texas either Tiny Scan TS-140 or 301 will plug directly into the Hisun diagnostic plug which I finally found when I took the bench seat out and opened the lid over the engine compartment and looked down the driver side of the Engine and found the wire laying way down beside the engine lifted it and low and behold there was the 6 pin diagnostic plug with a plug-in cap that has to be removed to plug in the scanner and replaced to keep dirt and stuff when finished. Hope this helps someone. Oh the 301 does a lot more like connect to iPhone, Android, or PC via WIFI with it's own IP address but is a little over $300 the TS-140 reads and clears codes and only costs $169.

  • Like 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Rschrem
      Hi, my 2010 Hisun will crannk but comes to a stop and only clicks.  It has new battery and solinoid. Battery connections all seem good. Any ideas what the problem is? 
    • By Xov
      Just received delivery of a 2024 AMP Pro.  Thought I'd start a thread with my impressions as I use it and learn more.  There doesn't seem to be a whole lot of real-world usage information out there on this model.  Hope this will help others as they research.
      Intended Use Cases
      Fire mitigation / slash removal from a 5 acre forested and well-gamble-oaked property.  The previous owners thought as much about fire mitigation as I do about fashion: not much. Snow removal Stump pulling General hauling (rock, lumber, etc.) Weimaraner energy depletion.  Wasn't an original use case, but a nice added bonus.  Experiences So Far
      Wasn't impressed that two of the bumpers on the underside of the bed where it sits upon the frame were missing.  The metal on metal contact has damaged the powder coating and the frame.  I expect a little better QC.
      I've only put a few hours on it, so not a ton to report on usage.  It isn't quiet; it's silent.  I can't even detect an electric note from the motor. I removed (and subsequently replaced) the motor cover noticed that the motor is German and made by Schambuller.  The motor controller is Italian and made by Dana TM4.  Given the operating specs of both I found on the web, I suspect both are higher quality than the previous Navitas (which is supposed to be decent).  The motor is rated at 25 hp and 71.5 lb-ft of torque.  It feels very powerful.  All the torque is delivered instantly, if desired.
      The bed is huge and has an electric dump as standard.  Great feature but would like it to go up a bit more.  Probably not feasible from an engineering perspective, but I want and I need ;).
      Power steering is nice, but vague.  Probably common to many UTVs, but I am accustomed to more direct results from input.  Plan early and plan often.
      In our first full day of usage, we hauled about 1/2 as much slash as the entire rest of the year when I was doing it by hand cart.  I may get fatter, but I'll also get more done.  After a few days of usage, the battery meter has gone down by 1/10th. 
      Until next time...


    • By Tim n Deb
      Riding out today it acted like it ran out of gas,  stalled and died and would not start.   Towed back to house,  New  plug added this past month,  plenty of oil, getting plenty of gas, battery cranks good.   Trys to kick in and starts but doesnt.   Two days prior while sitting at a idle it died.  Added gas and it started did my ranch chores with it.  But just now it stalled out cranks but will not start.   Tried to find if fault codes came up on the clock like manual says but not sure I am doing that right.  Any and all help apprecated.  Thank you
    • By monkthumper
      Fuel pump is good (i hotwired it) swapped relay with known good one no help. I'm leanin towards ECU but cannot find wiring diagram online. Dont know how fuel pump relay gets its signal, all fuses good, any help? 
    • By amiracle40995
      I’m getting a 700-7 every startup. I’m having to change the plug every 100 miles on 93 octane gas. I got a lower numbered plug that is supposed to burn hotter. I’m wondering why that comes up every time I start it and if it’s related? I included a picture of the code or whatever it is. I haven’t seen the code in the owners manual or the hisun shop manual I have. 

×
×
  • Create New...