Quantcast
Jump to content


Recommended Posts

Posted

As I have shopped around I have noticed the  sxs manufacturers leave out things I consider critical like a windshield and a roof counting on you buying extra stuff. 

Is there any advantage to buying accessories from the dealership when buying a new one? 

Is there any general quality difference between OEM and aftermarket accessories?

I also plan to buy a winch and am considering a Harbor Freight winch.  Thoughts?  Also, I've always thought the idea of a receiver mounted hitch makes lots of sense so you can use it on the front or back.  Has anyone seen this done?  Thoughts?

Posted

How you mount the winch, would probably depend mostly on what you expect to use it for. A receiver mount can be useful for being lightly stuck, and having an anchor point somewhat straight behind, or in front. A side pull from a receiver could be trouble. Especially if the buggy is buried. Receivers aren't made to take a side load, and aren't rated for that much weight anyway. Unfortunately I've found that optimum conditions rarely present themselves in a winching  situation. I always carry several tow straps, and lots of rope. Along with several shackles, and several snatch blocks. Although I rarely use any of it.

Power cables would be a pain, and expensive for the rear mount. I've found that winches in general are a pain. But occasionally it's the best tool for the job. Although I typically use a come along, and try to avoid deep muck. 

I will say this for certain. Get the kevlar rope, or similar. Cable is extremely dangerous under load. People have died after a steel winch cable snapped.  Cable will fray a bit, no matter how carefully you treat it. Leaving painful surprises along it's length, as you guide it back on the spool.

My vote would be for a front bumper mounted warn winch. With lots of accessories, and preferably a cordless remote, with a wired backup remote. 

FWIW, my buggy weighs around 1500pounds. My 4000 lb. Warn winch would almost certainly need at least one snatch block to pull it out of floor board deep mud. So go bigger than you think you need, if you'll be in serious back country. 

  • Like 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Rusmis91
      I’ve never been around Coleman Utv machines. Do they have a good reputation, durable dependability. Could you compare them to yamaha rhinos or Polaris ranger
       
      thanks in advance
    • By aguillory
      Anyone have a way of checking to see if a 2023 Ranger Crew 1000 roof will fit a 2017 Ranger Crew 900 ?
    • By didgeridoo
      Hello, All!  I've decided to replace the traction batteries in my 2018 Sector E1 with a 48V Lithium set. They may be expensive, but I figure the Discovery Dry Cell are, too. I am not looking for the max driving range, as I have never received near the brochured range to begin with, but a good mix of charge/ get work done/ charge is what I am expecting.
      I have settled on the 48V EAGL kit from bigbattery dot com. Each battery pack provides 30Ah. The kit ships with a charger, as well. The packs would be physically connected in parallel (using a busbar) to one another, maintaining the 48V voltage, but together would be able to provide the amp draw the buggy pulls when going up hill or towing a rake (rated 320 max continuous Amps). This is in comparison to the serial connection the eight 6V lead batteries. Each of the EAGL batteries looks to have its own BMS; am I correct in thinking I will have to use their included charger rather than (simply) changing the onboard charger to lithium mode? The chemistry of the pack is LiFe PO4, for what it's worth.  I haven't torn anything apart yet (to diagram), so  I am not sure how the dash will interpret the AMP draw, but the kit I am looking at includes a dash mounted charge indicator.
      If anyone has completed a similar conversion, do you have any tips? Specifically, how did you remove the original batteries, and how did you secure the new ones? I am guessing that almost any change from the stock batteries would involve at least some modifications. Any tips would be appreciated, especially things I may have failed to consider. Thanks!
    • By Blekntowkz
      I have an X3 Max and I currently run the Can-Am rearview mirror alongside a Swamp Donkey stereo system mounted to the roof. Is anyone here familiar with this exact setup? 
      I’m looking to upgrade to a proper can-am Maverick x3 max front windshield made of glass so I can run a manual wiper. Does everything clear the stereo and mirror mounts just fine, or are there clearance issues? Also, which glass windshields out there are actually worth spending the money on?
      I currently have the Can-Am hard-coated poly windshield, but I am really tired of not having a wiper and having to constantly stop and squeegee after hitting a few mud puddles or dealing with this Michigan snow, mud, and water holes!
      Any advice would be huge.
    • By AaronD1982
      Onto the next problem, everything has been replaced in the charging system except the Flywheel Rotor, I have it torn apart all the way down to said rotor, but it is suggested that a specific puller is required, and a compatible rotor seems virtually impossible to find.  I can find many like it, but this one is mine scenario for those that get the reference.  For all I know I have the last Massimo Buck 400S on the planet and will never find another part again, but who knows.  Any ideas, help or otherwise that anyone might have would be greatly appreciated.
×
×
  • Create New...