Quantcast
Jump to content

Where to start

Anthony Butler

By Anthony Butler
in Joyner UTV SxS Forum

 Share

Recommended Posts

Anthony Butler Apprentice

Anthony Butler

Posted
Posted

Long story short , 2009 Joyner trooper 1100 , 2300kms 

When you turn the key the gauges don't cycle, can't hear pump and fan doesn't turn on . Headlights work and turns over no problem . Doesn't even attempt to fire.  Fueses are good not sure about relays. 

Worked fine for a little half hour run , tried to start it a couple hours later and this happened. 

 

Where do I start checking 

Link to comment
Share on other sites
mixfixdave Enthusiast

mixfixdave

Posted
Posted
Long story short , 2009 Joyner trooper 1100 , 2300kms 
When you turn the key the gauges don't cycle, can't hear pump and fan doesn't turn on . Headlights work and turns over no problem . Doesn't even attempt to fire.  Fueses are good not sure about relays. 
Worked fine for a little half hour run , tried to start it a couple hours later and this happened. 
 
Where do I start checking 

Check the fuses behind the drivers seat and passenger floor area. The fuse boxes are weak links and sometimes get dirt and crud in them causing bad connections at the fuse terminals.
I’ve got 7k hard miles on my 2009 T4 and it’s been fairly reliable.

Make sure you have fuel/pressure and spark!
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • CYJSP2009
      Joyner parts
      By CYJSP2009
      Dear Joyner owners
      Any one who is looking for below Joyner parts please send email to casey from Leaf Asia  ( please send to [email protected] and cc to casey2leafasia.biz & [email protected])
      Currently, we have supply below parts: 
      1.  cv axles, cv rebuild kits, cv boots
      2.  Differentials and differential ring and pinion set
      3. Cables, 
      4. Brake parts
      5. Engine parts
      6. Other parts. 
      We will provide better price, close follow up ... 
      We can arrange productioni for parts that we can collect demands from customers  
      Have a good weekend
      Casey /  Leaf Asia 
      2023-11-17
       
    • Nathon S.
      Bennche 700 EFI Bighorn New Fuel pump not working
      By Nathon S.
      I have a Bennche 700 EFI Bighorn. I’ve recently been unable to get it to start. After a little troubleshooting I realized my fuel pump was not pumping fuel. This weekend I emptied the gas and replaced it with new. I replaced the fuel pump, fuel filter and fuel injector. I also replaced the battery, spark plug and made sure all my fuses and relays were good. I have confirmed that the float on the fuel pump is not obstructed. The UTV is about 12 years old and has less than 100 hours on it. It has not run in over a year.  Not sure whats going on?!? After doing a little reading I'm leaning towards it being an issue with the ECU or perhaps a faulty wire in the wiring harness. Anyone have any ideas on where to start looking or what I could be dealing with? Any help is appreciated, thanks in advance!
    • skittle021
      Super Weird Problem with Primary Shave/Clutch...
      By skittle021
      So I've got a Hisun 550 that I was doing some work on that required removing the CVT and it's housing. Upon attempting to reinstall the clutch, sheaves, etc, I found that the belt no longer fits - it's far too wide. None of the parts have been replaced, they're all OEM. Exactly the same parts as what I took off a few weeks ago.
      To be more specific, my belt is 1.25in wide, but the gap between the clutch and the primary sheave is only 7/8in wide. I'll include a few photos to explain.
      Has anyone ever experienced such a bizarre problem? Any help at all would be appreciated, I've been stuck on this for a month. I'm open to just about any suggestion.
      Photos: 
       





    • packersfan
      Hisun 500 very hard to turn
      By packersfan
      I have a hisun 500 got from a auction and when turning a corner left or right it's a two hand job then when you left go snaps back.any help on what to look at would be appreciated.
      Also blows blue smoke until she gets warm then it's ok 
    • MJG
      Looking to Purchase 2008 Joyner Renegade
      By MJG
      Hello, 
      I found an 08 Renegade for sale and looking to purchase it.  I haven’t heard too much about these machines and any insight would be much appreciated.  Are they good machines?

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...