Quantcast
Jump to content


2015 ODES 800 non start

Max M

By Max M
in ODES UTV SxS Forum

 Share

Recommended Posts

Max M Newbie

Max M

Posted
Posted

Removed from winter storage and starter not working. Replaced battery and starter relay. No good . Relay clicks when key is turned but no action at starter. Removed starter and it worked fine on bench. Is there a in-line switch or contact that could be bad?

ElbowRoom Rookie

ElbowRoom

Posted
Posted

I had a very similar problem with a 2018 Odes 1000. I had a loose ground on passenger side of engine (for Odes 1000). This might not be your problem but it's something to check.

Garry Rookie

Garry

Posted
Posted

I just purchased a 2013 800 Dominator and the ignition switch is finnicky...meaning sometimes the only way it will start is to only turn the key about 2/3 of a turn vs all the way to the stop. Its a different issue than yours as my starter will actually spin but it wont actually fire/start until I back it off slightly.

I have never owned one of these before so I am learning as I go.

 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Rschrem
      2010 700 Hisun starter issue
      By Rschrem
      Hi, my 2010 Hisun will crannk but comes to a stop and only clicks.  It has new battery and solinoid. Battery connections all seem good. Any ideas what the problem is? 
    • Homeowner A
      Replacement Battery UTV 400
      By Homeowner A
      What's the best replacement battery option for a Coleman UTV 400?  
    • SkyPilot56
      working on a coleman 550 out fitter
      By SkyPilot56
      working on a coleman 550 out fitter , had a shit load of codes, coil, injector , and the map sensor for fuel injector replaced all 3 and figured it would start , but no joy have spark (new plug also and inline fuel filter) cleared the codes and still have the engine light , turns over fine but damn thing still will not start, friends daughters were driving it and turned it off to park , and went back to start it and same thing turns over but will not start , with this machine anyone have any ideas as to what the hell , I should be looking for , no plug's unplug checked wires none seem to be pulled apart or broken !
    • Mike Jenkins
      2013 hisun 700 will not run, cranks fine
      By Mike Jenkins
      I have a 2013 Hisun with a 686 Yamaha engine.
      I purchased it from an individual and it ran fine as long as the battery was full.
      I replaced the stator and now it will not start (run).  It cranks fine, has fuel pressure, but will not fire up.  I replaced the coil, no luck there.
      a technician told me that it was the wrong stator and wants a mint to replace it.
      the wires all plugged in when I installed the stator.
       
    • didgeridoo
      Hisun Sector e1 Battery replacement: any tips?
      By didgeridoo
      Hello, All!  I've decided to replace the traction batteries in my 2018 Sector E1 with a 48V Lithium set. They may be expensive, but I figure the Discovery Dry Cell are, too. I am not looking for the max driving range, as I have never received near the brochured range to begin with, but a good mix of charge/ get work done/ charge is what I am expecting.
      I have settled on the 48V EAGL kit from bigbattery dot com. Each battery pack provides 30Ah. The kit ships with a charger, as well. The packs would be physically connected in parallel (using a busbar) to one another, maintaining the 48V voltage, but together would be able to provide the amp draw the buggy pulls when going up hill or towing a rake (rated 320 max continuous Amps). This is in comparison to the serial connection the eight 6V lead batteries. Each of the EAGL batteries looks to have its own BMS; am I correct in thinking I will have to use their included charger rather than (simply) changing the onboard charger to lithium mode? The chemistry of the pack is LiFe PO4, for what it's worth.  I haven't torn anything apart yet (to diagram), so  I am not sure how the dash will interpret the AMP draw, but the kit I am looking at includes a dash mounted charge indicator.
      If anyone has completed a similar conversion, do you have any tips? Specifically, how did you remove the original batteries, and how did you secure the new ones? I am guessing that almost any change from the stock batteries would involve at least some modifications. Any tips would be appreciated, especially things I may have failed to consider. Thanks!

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...