Quantcast
Jump to content

2017 Hisun 500 vector utv starting issues


Michael R

Recommended Posts

Wife said UTV stopped running and cannot restart. I checked the battery, it was good. I checked the fuse box, no blown fuses. Whe I tried to start, the starter had a thump noise one time, and the starter relay wires were hot. I replaced the relay, nothing. I then replaced the starter and still the same symptoms. It won't start and relay wires hot.  Any ideas what to check next- perhaps ground strap of which I have no idea where it would be, or perhaps a new fuse box with new relays?

Link to comment
Share on other sites

Based on those symptoms I would remove and bench test the starter next. It sounds like there may be an internal short.

Remove it and clamp it to the workbench. Connect a battery with jumper cables to the ground, and tap the terminal briefly with the positive cable and see if it spins like it should. My guess would be it doesn't. 

Link to comment
Share on other sites

From the text you wrote, it seems that it stopped running while your wife was operating it. At that point, she tried to re-start it without success. Does it turn over? If it does, look to the ignition, if not; does the starter get voltage while trying it? If it does and the engine won't turn over the engine might be siezed. If it doesn't look to the relay. Is there voltage going to the relay but not going through during start up, then it's a relay. Your volt meter is always your best friend. 

Link to comment
Share on other sites

On 8/1/2022 at 10:14 PM, Michael R said:

Wife said UTV stopped running and cannot restart. I checked the battery, it was good. I checked the fuse box, no blown fuses. Whe I tried to start, the starter had a thump noise one time, and the starter relay wires were hot. I replaced the relay, nothing. I then replaced the starter and still the same symptoms. It won't start and relay wires hot.  Any ideas what to check next- perhaps ground strap of which I have no idea where it would be, or perhaps a new fuse box with new relays?

If it were my machine, (MSU 800) I'd take the screw cap off the end of the magneto, using the correct size Allen wrench make sure the engine isn't stuck, "froze". Can't say for sure on that 500 if that's how to check it. I'm sure there are some here that can tell you. Aefron88 for one.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By malenurse13
      We just bought a used 2017 American Landmaster TW450. No hour meter that I can find, so not sure exactly how much it has been used. 
      The first 2 days we had it, the starter was a little sketchy, but it started after 2-3 tries. Sometimes when turning the key, we would hear a loud metal "clink" sound. Like the starter made contact, but didn't have enough power to turn. 
      THIS MORNING... Turning the key, we hear a single click sound. That's it. Even with a new battery, the starter is still doing the same thing. Both batteries (old and new) were reading 12.8 volts on volt meter. So I'm wondering what else could be going on? Any ideas on what to look for would be greatly appreciated...
      Thank you!
    • By Chucky 1
      I purchased a new 2023 Landmaster UTV L4 in October of 2023.  UTV didn't seem to have as much power of the demo L4 that I drove but figured once it broke in it would be better.  After about a week the unit started bogging down backfiring and stopping.  Gas fumes really bad, wait a few minutes and it would start up again.  Brought it back to the dealer and after keeping it for a few weeks said he couldn't find anything wrong with it.  Got it back home and it started acting up again, brought it back to dealer a week later and he said he found couple things that might cause it to do run bad and he was able to replicate the issue but didn't really know what was wrong.  Got it back home again after being at dealer for several weeks and the unit started running bad again right away.  Brought it back to dealer and he went back and forth with Kohler about possible fixes but just checked somethings and try to swap a few parts but still runs bad.  I called Landmaster HQ to speak with someone about a refund and was told that was handled at the dealer level.  Dealer called Landmaster and they told him they didn't do refunds or exchanges especially with units that had problems.  The dealer is now trying to get a new engine to but I have not heard anything as of yet.  I did file complaint with Better Business Bureau and they accepted my claim and reached out to Landmaster.  The National Service Manager called me and said the he had been contacted by the BBB about the complaint and he would look into it.  I told him that I would just like to have my down payment of $2,000.00 returned and never mind the over $1,000.00 I have paid in notes for a UTV that I cannot even ride on without hoping it gets me around the neighborhood.  I have found out that the 2024 Landmaster UTVs will have Vanguard engines due to issues with the Kohler engines.  Very disappointed in what is "Proudly Made in the USA" and the way Landmaster has treated this disabled veteran! 
    • By Richard shepard
      I have a 2021 colman 400utv engine will start and idle, as soon as you hit throttle to move engine dies and will only start when you throttle it, let off throttle it dies, I replaced the injector and plug still the same, anyone have any other ideas
    • By Robert B
      Going down a 20 deg hill engine is holding UTV back. Then something releases like going into Neutral and makes a loud clacking noise. Have to use brake to slow UTV down. Then once level it shifts back into gear. Have done shift extension does not pop out of gear.
    • By DJ Brusenski
      checked all the fuses and relays, I can jump start it with the key in the on position. it will not key start need some help, thanks
×
×
  • Create New...