Quantcast
Jump to content


Recommended Posts

Posted

my hisun 400 has ben leaking oil out of a small metal tube on the bottom near the oil filter. Got the side by side given to me after been sitting for a couple years  but 2 quarts in nothing happened my buddy went and worked on it and put another quart in it. i thought it just pushed out what it didn't need. but its dry as a bone inside. does have a good clatter coming from the top end as well, with oil in it. looking for some help not much on the internet about these things.

Posted

Hey Trevor,

Do you have a picture so we can try to help figure out what it is?

Don't run it low on oil, it only holds like 2.5L so 2 low is more or less empty. Running it empty of oil may cause it to self destruct rapidly, which may explain the rattle.

  • 9 months later...
Posted

Mine is doing the same thing! Why isn't their any info for these things online? Same story with me. Bought it for cheap from a family member that couldn't get it running. I got it running but oil was very low. I added oil and it leaks from a tube on the bottom of the engine near the filter. 

  • 3 weeks later...
Posted

I took a picture of it but I can't figure out how to post it here. I'm currently not home to take another one but it is dripping out of a steel nipple that points straight down near the oil filter under the driver's seat. It just drips slowly and after sitting for about three weeks in my barn it looks like at least a quart has dripped out. 

  • 8 months later...
Posted
On 5/29/2023 at 7:19 AM, Casey said:

I took a picture of it but I can't figure out how to post it here. I'm currently not home to take another one but it is dripping out of a steel nipple that points straight down near the oil filter under the driver's seat. It just drips slowly and after sitting for about three weeks in my barn it looks like at least a quart has dripped out. 

there's a nipple under the oil filter that is the water pump weep hole. It shouldn't have oil coming out, you may get a tiny bit of coolant from time to time if the water pump seal is weeping. if theres a flow the water pump seal has failed and you'll need a new water pump.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Popular Now

  • Similar Topics

    • By rdc
      I posted this before , but I had the year wrong. The part I need is for a 2014, I don't know what all years will work, but I need the 2 bearing style with the spacer in the middle. It looks like this pic. If anyone has one I'll buy it rite away. my email is [email protected]. Thanks, RC

    • By Burk
      I have a 2021 Axis(Hisun) 700 from Lowes. Will not start. Checked starter, solenoid, spark plug and fuel pump. Everything seems to be fine. The motor turns over and will try to start but just will not. Battery is also good. Frustrated!
    • By HISUN Sector 750 EPS Failu
      "Mrs. Smith" doesn't like how loud our Sector 750 is.  On a HISUN forum someone said the same thing about his 750.  I haven't given it much thought because I've been more focused on stuff that has broken.
      So, I used my decibel meter to check ours out.  4000 RPM, Low gear, under 20 MPH . . . . 97 decibels.  That's above most ordinances, even state boat noise limits.
      AI Overview Ninety-seven (97) decibels is considered very loud and dangerous to hearing with prolonged exposure, roughly equivalent to a newspaper press, a loud nightclub, or a snowmobile. At this level, damage can occur after just 30 minutes, necessitating hearing protection
    • By Mitch13
      2022 Coleman 400 with 13 hours on the engine and the mice got to it. Every wire coming out of the steering column in one cluster has been eaten through. I tried reconnecting matching wire colors to each other and I get the left turn signal and hazards to work, nothing else. If I play around a bit I can get the horn to honk or headlights to come on but only when I connect them to the brown wire. Obviously I don't know what I am doing here. Does anyone have a picture of how these wires are connected when they are under the hood on the drivers side coming from the steering column?
      Gray - seems to carry power
      Brown - left turn signal
      Green with purple stripe - hazards?
      Pink with red stripe - horn?
      Green - head lights?
      Yellow - head lights?
      Yellow with red stripe?
      Blue?
      Dark green?
      There is also a bundle hanging under the hood not connected to anything green with yellow strip, brown and blue?
      Other than that issue, I am about ready to sell this for parts if you interested let me know.
      Thanks
    • By Hunterman22
      Can anyone please tell me or send a link as to how & where to hook up a code reader to my 2021 Hisun 500 Axis.  I have a 6 pin to a 18 pin  adaptor and the blue cord VAG KKL adaptor .Just not sure where or what to hook up to. Can I use your typical vehicle code reader or do I need to download something on a laptop or PC???
       
×
×
  • Create New...