Quantcast
Jump to content


Recommended Posts

Posted

I was looking at purchasing a 2017 Hisun vector 500, used of course.  The seller is selling it cheap stating the machine had "an unknown oil leak" and his kids ran it low on oil causing the timing chain to brake.  I am not familiar with small engines, but with what is being described, wouldn't this result in some damage to other internal components as well?  Just trying to get an idea if the machine is worth fixing or would it likely need a complete engine/overhaul to make it right before I entertain the thought of purchasing it.

  • Alex changed the title to 2017 Hisun Vector 500 Timing Chain broken
Posted

It may or may not have damaged the valves. Either way it's a fairly large project to replace. Not sure on the 500, but complete assembled heads for these things are not crazy expensive (a couple hundred $) so for then right price if you're willing to put the time and labor in it could be a good deal.

Posted

I wouldn't worry too much about the valves or head damage as I have seen timing chains break and do no damage.  What you will have to do is check if the engine has compression and  if that is good (making sure that the valves are closed of course).  Then take off the valve cover (and maybe the head) along with the flywheel, stator etc. and replace the timing chain.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Popular Now

  • Similar Topics

    • By rdc
      I posted this before , but I had the year wrong. The part I need is for a 2014, I don't know what all years will work, but I need the 2 bearing style with the spacer in the middle. It looks like this pic. If anyone has one I'll buy it rite away. my email is [email protected]. Thanks, RC

    • By rdc
      Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]
    • By Burk
      I have a 2021 Axis(Hisun) 700 from Lowes. Will not start. Checked starter, solenoid, spark plug and fuel pump. Everything seems to be fine. The motor turns over and will try to start but just will not. Battery is also good. Frustrated!
    • By HISUN Sector 750 EPS Failu
      "Mrs. Smith" doesn't like how loud our Sector 750 is.  On a HISUN forum someone said the same thing about his 750.  I haven't given it much thought because I've been more focused on stuff that has broken.
      So, I used my decibel meter to check ours out.  4000 RPM, Low gear, under 20 MPH . . . . 97 decibels.  That's above most ordinances, even state boat noise limits.
      AI Overview Ninety-seven (97) decibels is considered very loud and dangerous to hearing with prolonged exposure, roughly equivalent to a newspaper press, a loud nightclub, or a snowmobile. At this level, damage can occur after just 30 minutes, necessitating hearing protection
    • By Kierobi
      Have a MSU 500 that we got from my wife's uncle a while back. We've had it running and hauling around the property but it stopped a few months ago after what I thought was running out of gas and I'm just getting to looking into it. 
      Had fuel to the injector but nothing coming out the injector so swapped with new injector and installed inline filter in the supply hose from fuel pump. Tried again and still nothing but noticed this time that I can't hear the fuel pump priming. 
      Pulled off the electrical connection and I'm getting 12V to the fuel pump but it won't run. Put it on a test bench and got it to run so put test lamp between +ve and -ve terminals on the connector and nothing. Checked against the passenger seat securing post and get a light. 
      Tried chasing the wire back and think that the ground is through the ECU but not 100% sure. Can someone confirm for me? And if it is through the ECU, is the ECU just grounded against the frame or is it wired through to the battery?
      Thanks in advance and hope this all make sense!
×
×
  • Create New...