Quantcast
Jump to content


Recommended Posts

Posted

Most of the time my 500 runs fine.  However twice now, after I had been running the marching for a while I have had issues with it stalling when I put it into gear.

It will start and idle fine, but when I try to put it into gear (forward or reverse) the engine stalls.  Both times I was finally able to get it to turn well enough to get home by starting the engine, pushing the 500 then while moving put it into gear.  After that it ran fine, including while stopped.

 

I have pulled the cover off of the belt, and everything seems to be fine.

 

Any thoughts/suggestions on what to check?

 

Thanks!!

Posted

So have to push it while in neutral THEN while it's rolling, slam it into gear.

That is not good on the transmission. 

Even when the engine is running, the clutch should not be engaged until there is higher RPM. Then the engine spins the clutch, the paws on the clutch slings out and engages the clutch drum. The drum spins the primary sheave. Primary sheave spins the cvt belt. Cvt belt spins the secondary sheave. Secondary sheave is on a shaft attached to transmission. 

 

Now the clutch is a wet clutch. It uses a special engine oil for wet clutch motorcycle, ATVs and such.

Is it possible it has the wrong oil? 

Possible air filter?

Possible fuel filter?

Since it doesn't happen all the time it will be hard to test. Maybe the next time it happens. Jack up the machine so wheels are off the ground. Start again and put in gear. See if it stalls again. I just don't know enough to help. Sorry.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Tim n Deb
      Riding out today it acted like it ran out of gas,  stalled and died and would not start.   Towed back to house,  New  plug added this past month,  plenty of oil, getting plenty of gas, battery cranks good.   Trys to kick in and starts but doesnt.   Two days prior while sitting at a idle it died.  Added gas and it started did my ranch chores with it.  But just now it stalled out cranks but will not start.   Tried to find if fault codes came up on the clock like manual says but not sure I am doing that right.  Any and all help apprecated.  Thank you
    • By Flanman55
      I have purchased a used Supermach700 (2008), It runs great after a new choke cable but. The temp sensor on the thermostat house is unhooked and can not find where it plugs back in. The fan has been un hooked from the sensor in the rad and cant figure out how it goes back together properly.  The fan was wired to a by pass switch and i just always leave it on but would like to work it properly. I assume the sensor went bad and not changed.
       
      any help would be great.
       
      thanks
    • By KWinTX
      I just bought a new 2024 Hison 550 Stryker 2 months ago. this is the second time I have had this issue.  It only has about 20 hours on it. The last time it happened we took it back to the dealer. it was a fuse.  Since we live three-hour time driving there and back. I would like to find another solution if possible.  I have tried all the fuses that seem to have anything to do with starting.  Currently checking the battery. The battery is new. it came with the unit. It is probably 6 months old.  the UTV has all power to everything electrical. lights turn signals and radio all work.  When trying the key to start . it is 100% dead. as in it doesn't even click.  There is a low whirring like the fuel pump is turning on though. The Unit was running and driving just fine.  we shut it down for the night. The next morning my wife found it in this condition.  Thanks for any Ideas or solutions???   Otherwise, it goes back to the dealer tomorrow. Just hope I didn't buy a lemon. Great little UTV when it does run.😅  anyone else ever have this Issue..? 
    • By GunnersTacklebox
      Hi All,
      New here, but bought a 2022 Sector 750 brand new last march (old stock up here in Canada)
      It's a good bike so far, but I have noticed a quirk and was wondering if anyone else has had a similar issue?
       
      The issue I've had is if I leave the utv parked on any incline, not even a major incline, and leave it to sit for a while (day or two) it will not start properly. It will turn over and not fire until I press the gas pedal, when it will run and rev up, but if I let off the gas it will die. It will keep doing this until I either start it in gear and drive it for a bit or leave it in neutral and roll it down the hill to flatter ground. where it will have to sit for a while. 
      If I park it on a decline there is no issue. fuel is not low, it's occurred a couple times now. 
       
      Any thoughts on the cause of this? Dealership just says bring it in and let them take a look, at my expense of course. 
    • By Mike Jenkins
      I have a 2013 Hisun with a 686 Yamaha engine.
      I purchased it from an individual and it ran fine as long as the battery was full.
      I replaced the stator and now it will not start (run).  It cranks fine, has fuel pressure, but will not fire up.  I replaced the coil, no luck there.
      a technician told me that it was the wrong stator and wants a mint to replace it.
      the wires all plugged in when I installed the stator.
       
×
×
  • Create New...