Quantcast
Jump to content


Recommended Posts

Posted

Well tore apart the rear end and to my surprise is a lot of metal in the bottom. Further into it I've found that my ring and pinion are trash. I noticed that the ring bolts have been drilled and safety wire installed but they are the factory bolts. I need a parts list for upgrading it and am looking for a ring and pinion also. Feel free to ask me any questions. And all input is highly appreciated!

Posted

I think I may have a ring and pinion. I replaced my original trooper ring and pinion with the commando ring and pinion as I wanted more low end power. I had put 30 inch tires on and so I wanted more low end. I will look and if I can locate i will PM you. Might take a day or two but will try and locate.

  • 5 weeks later...
Posted

Hey guys!

Well back to the rear end on my trooper.

I didn't pull the rear apart yet but I have a knocking sound in the rear end just like last time! Going to say it's one of the center pins.

So first question is does anyone else had this issue? And 2 I will be looking for pinion shafts again. So please let me know if anyone has one.

Thanks!

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Similar Topics

    • By mrpro
      I got the fronts adjusted.  I'm trying to raise the ride height in the rear, but my spanner wrench keeps slipping.  Is there an easier better way?  It's like there's too much pressure working against me to be able to twist the height adjusters.  How can I relieve that tension to make them easier to turn?  
    • By Jeff freeman
      I have a Coleman 550.  Was having problems to start with where it would start and then shut off after a couple tries. It would take off and be good. It then got to a point where it would not start at all. I replaced the fuel injection twice the second time I replaced it I noticed a mouse or something had chewed one of the wires that connect the electrical to the fuel injector. . So two-part question first does anybody have a part number for that wire harness?  Second, any other ideas after I fix the wire harness permanently on what could keep it from starting I have gas flow up to the fuel injector.


    • By rdc
      I posted this before , but I had the year wrong. The part I need is for a 2014, I don't know what all years will work, but I need the 2 bearing style with the spacer in the middle. It looks like this pic. If anyone has one I'll buy it rite away. my email is [email protected]. Thanks, RC

    • By rdc
      Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]
    • By Sidewinder
      All mid 2008 through 2014 Polaris RZR 800 series have a big problem with the rear differential pinion nut backing off, allowing the pinion gear to shoot into the rear differential, destroying the rear differential. This has happened with machines with as little as less than 100 miles on them! Reports indicate that there are no problems, nor warnings, until the rear differential grenades, locking the rear axles solid! This requires the machine to be lifted onto a trailer, to be transported for rear differential replacement, as it destroys the case. After failure, rear differential replacement can be quite expensive: labor alone can run from $800-$1200 and a new OEM Spicer rear diff, if you can find one, can run from $1700-$2500! So, if you own any Polaris RZR 800 series between the years of 2008-2014, I recommend that you do this repair before further use of your machine. personally, I have grounded my machine until it can be done. Please check the online post for your own awareness.

×
×
  • Create New...