WTB Transmission for Sand Viper 1100
-
Similar Topics
-
By nascarcamshaft
I have a 2009 Trooper that when I first start it it runs great but after about a min it starts to cut out under acceleration but clears out when it gets revved up. I downloaded the manual from Joyner-usa.com but it doesn't help much, Mine doesn't have a OBD port on it and my son who is a mechanic said he can wire one in if we have a wiring diagram for the CPU but the wiring diagram of the CPU that is in the manual is for a 3 cylinder engine. The manual talks about a MIL light that can flash out a code but I don't know where that is and even if I did find it they don't tell me how to read it. I have tried the coil and the map sensor and that didn't help I checked the TPS and it checks OK. I emailed Joyner and all I got from them is there should be a OBD port on it and then they said they checked and found some don't have it, No help from them. Anybody run into this problem or know were I can turn to get some help on this, even a good wiring diagram of the CPU would be a big help.
Thanks for you help
-
By abernot
Hi all...I am looking for a reliable mechanic near the last Vegas area to help maintain my 2016 Sand Viper 1100cc. Any suggestions?
-
By abernot
Hello,
First time buggy/UTV buyer here and I have been looking at a 2016 Joyner Sand Viper 1100cc.
First of all, and overall comments on that particular model or recommendations? I am a very amateur rider and am just looking to have some occasional fun in the surrounding desert areas of Vegas as well as do some low key canyons and small mountain areas.
Main question is, what are the options to tow the buggy aside from trailering it? I have been looking into a tow bar but am finding very limited information on anyone installing a way to connect a tow bar to the rig and tow it that way. Any insights are greatly appreciated!
-
By 180gtr
Parting out a rolled Sand viper 1100. I will list some of the parts I have, otherwise ask me if there is something specific you are looking for. I am selling everything I have for $800. I am located near Glenwood Springs CO.
SOLD ITEMS, I do not have these items.
Wheels
Tires
Engine
Transmission
Axles
Shocks
Control Arms
Things I have....These all came off of the running engine. I have video of it running if anyone needs to verify that.
Throttle Body $90
Starter $150
Alternator $150
Fuel rail, injectors, fpr $100
fuel pump $70
Map Sensor $50
Full set of Guages $150
Exhaust w cat, O2 SOLD
Ignition Coil - SOLD
Wiring harness and ecu SOLD
Radiator, shroud, elec fan, overflow tank $200
Fuel tank w sender $150 Has dent at base of fuel neck, no leaks
I have a box full of misc bolts, nuts, etc.
I will sell the Chassis or Frame alone for $200. The chassis is in pretty good shape, needs some cage repair and 2 areas straightened where control arms mount. If anyone had an automotive frame machine it would take a few hours.
That would include....
Brake calipers, lines, pedal, master cyl, E brake assy,
Steering shaft, wheel
Ignition switch, key
Light bar frame, 2 lights
misc hardware, spindles
2 hubs, rotors
Engine mounts
Throttle pedal, cables
Shifter, cables
Clutch master, pedal
I am sure I am forgetting something.
I am parting this out of ebay right now, I just picked up another project and could use the room. No I will not take less than $700 for all of it or $200 for the frame. I do not need to sell it, I will make far more parting it out but would like the extra space in the garage.
If interested I also have an 07 1000rr engine setup I would sell with the buggy for $650.
Thanks!
-
By Travis Sparks
looking to buy joyner complete with title problems ok in tn ky va area 100 miles within knox tn area txt what you got 423 626 0995
-
