Quantcast
Jump to content

'98 Mule 2510 nightmare


Recommended Posts

So, this unit comes in for hard to start, wont idle, and have to throttle and choke it to keep it running. Of course higher RPMs make shifting into gear awful.  It has the FD620D engine, 808 hrs, ranch vehicle but not abused. I rebuilt the carb, (the right way with dip soak and all the brass), replaced plugs, fuel filter, checked fuel flow from pump, dumped tank and put in fresh gas. It runs some better, but still wont idle or midrange without 1/2-3/4 choke. Very lean, but flowing good amount of fuel through main jets. I've checked for vacuum leak(s), and none found.

I have checked coils for proper resistance and found slightly above spec readings across primary terminals but secondary ok.  My query is, can the igniter box go out of "calibration" and change the timing on the coils and cause an advanced condition? The engine does "kick" once in a while when starting it. This could also cause the engine to seem to run lean.

Any suggestions are  greatly appreciated. I prefer that it be the "box" to change rather than the space-locked rear coil! What the hell were they thinking?!

Thanks in advance .

Dan

 

 

 

 

 

 

 

 

 

Link to comment
Share on other sites

Any chance of swapping the carb with a known good running one? I know that you feel confident that's not the problem any longer. But it sure sounds like it's a carb issue. Since you've said it runs pretty good with the choke. Maybe some crud got missed, or a float, or jet problem causing this? From the description it sounds like a fuel issue. Can't help you on your specific question about the igniter box though.

Link to comment
Share on other sites

Thanks for the thoughts. The funny thing is, even running for a short time with the choke partially closed, the plugs really soot up. That tells me its  getting more fuel than it can burn properly.  And these $275-300  carbs aren't a common inventory part.

  • Like 1
Link to comment
Share on other sites

  • 2 weeks later...

Your symptoms sure sounds like the idle circuit in the carb is plugged or otherwise restricted.  The reason it runs a little better with the choke and/or partial throttle it because that's bypassing the idle circuit and you're running on the high speed circuit.  I would also check the float level.  That can cause excessive fuel (rich condition) that can cause sooting of the plugs and flooding of the engine.

Both conditions can cause hard starting and rough running engines.  Lesson I learned in high school auto shop long, long time ago before fuel injection was discovered.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Steve B
      My "R" light on the dash will not go out when I take the UTV out of reverse and put it into any other gear. Is this just the light switch issue or will this effect engine performance in the other gears?
    • By malenurse13
      We just bought a used 2017 American Landmaster TW450. No hour meter that I can find, so not sure exactly how much it has been used. 
      The first 2 days we had it, the starter was a little sketchy, but it started after 2-3 tries. Sometimes when turning the key, we would hear a loud metal "clink" sound. Like the starter made contact, but didn't have enough power to turn. 
      THIS MORNING... Turning the key, we hear a single click sound. That's it. Even with a new battery, the starter is still doing the same thing. Both batteries (old and new) were reading 12.8 volts on volt meter. So I'm wondering what else could be going on? Any ideas on what to look for would be greatly appreciated...
      Thank you!
    • By lonerider98
      At the end of last year my Coleman UT 500 will not go into reverse. I can hold it over toward the reverse to move it nut it won't lock into reverse. Anyone have this problem? Winter is just about over and going to have to get this resolved. Thank You!
    • By Hugh
      My 2018 Hisun sector crew engine cut off after about 15 minutes run. There is no indicator of what is wrong, no error code just die and won't restart until it cool down. I notice that the fan is not running but the temp indicator is on low temp, no overheat indicator. I checked the radiator fluid, it is cool to touch.
      Cooling fans are working, I can hear it running once awhile if I can get the engine warm up enough.  Thank you for all the help.
       
      Hugh
    • By packersfan
      I have a hisun 500 got from a auction and when turning a corner left or right it's a two hand job then when you left go snaps back.any help on what to look at would be appreciated.
      Also blows blue smoke until she gets warm then it's ok 
×
×
  • Create New...