Quantcast
Jump to content


Recommended Posts

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Topics

    • By JDawg
      Was using the machine all day to haul wood...no issues until the end...
      When I try to start it, the dash lights come on but starter does not...seems like no power to the starter.
      It is in park, but when I put the brake on to start, it registers N.
      Won't start in neutral either...
      Tried rocking it, did not help...
      Help...
    • By hisun junk
      As I tried to do a conversion with the Yamaha 660 motor, I realized the 660 was never fuel injected so it would not work for the fuel injected hisun motor swap. But the good thing is the hisun 750 motor is a clone of the 660 Yamaha but with the components for the fuel injection (cam/crank position sensor). So that left me with a new rebuilt Yamaha 660 and still a broke 750 hisun motor. I took apart 750 think the timing chain had broke from all that I've heard about these motors. The chain was not broke, but just off cam and crank gears! The chain tensioner was at fault!  I've ordered Yamaha 660 replacement parts, chain, two exhaust valves (which got bent when chain came off while motor was spinning) and seals. The piston has 2 little nicks where it had hit valves but no damage otherwise. The head is being redone at the machine shop and I'll be putting it back together in the next couple of weeks. Also I finally tracked down a Service Manual with all the info on the 550/750 Challenger.

    • By Jacob E freeman
      I have a 2018 cub cadet challenger 750 I bought brand new almost 2 years ago the first month I had it the exhaust broke and burnt the spark plug wire in two that was a recall so the dealership installed the new one it had a different design and it bolted up to the bottom two plugs below the spark plug the dealership said they had to Adjust the exhaust valves I get the machine back thanking everything is good now wrong not even a week after I get it back the timing chain tensioner comes apart inside the motor I take it back to the dealership They put one on I get the machine back thanking everything is good but then just like before not even a week goes by when I was riding the Machine automatically quits going come to find out the wet clutch was burned up the primary clutch head stripped off of the splines I get that fixed and then  it overheats I take it back they bleed the air out of the coolant they bring it back to me the same day that I get it back it overheats again I take it back they temporarily fix it again just enough to let the warranty run out and now the machine has been to multiple different mechanics I have had them try to bleed the air out they have stood it up on its end I have had the water pump changed I have had the fan hooked to a switch so I could leave it on all the time but still almost 2 years later not even 200 hours on the machine and I cannot ride it The dealership will not take it back as a lemon I have tried I am at my wits end I have no clue what to try next
    • By amiracle40995
      I’m getting a 700-7 every startup. I’m having to change the plug every 100 miles on 93 octane gas. I got a lower numbered plug that is supposed to burn hotter. I’m wondering why that comes up every time I start it and if it’s related? I included a picture of the code or whatever it is. I haven’t seen the code in the owners manual or the hisun shop manual I have. 

    • By Gary T
      I generally use my challenger for light duty misc. use, and for plowing. The one thing I dislike about this machine is the difficulty in shifting. I've had it the shop and they adjusted the shifting lever, but I still have issues. Some times it shifts ok, but the problem is it is hard to get it to move the lever from high to reverse or low to high or from any gear to the other. Seems I always have to accelerate a little to get it to engage to what gear I need it to go to. This is definitely not normal.
×
×
  • Create New...