Quantcast
Jump to content


Mule 550 front wheel bearings

Travis

By Travis
in Kawasaki UTV SxS Forum

 Share

Recommended Posts

Travis Grand Master

Travis

Posted
Posted

I think the front wheel bearings need replaced. Lately i've noticed some noise from the front end while driving.. jacked it up and both sides have considerable play. The passenger side more so. Kawasaki 92045-1170 replaces the bearing. its 2 per hub. which is 4. it's 25 bucks PER BEARING. which is $100 and some change for both sides. Kawasaki lists that the bearing used  is a  60/22 2RS ball bearing. i can find them anywhere from $5 to $10, BUT i question the quality, no country of origin is disclosed.

 Pivotworks.com has a front set but its $42 for each side. 42+42= 84, so thats better than 100..... any one ever bought anything from pivot works?

 I checked the local auto parts stores for the bearing but nada.

 

 
Travis Grand Master

Travis

Posted
  • Author
Posted

I looked on the pivots works kit some more, and the kit is 42.00 for BOTH sides. so all 4 needed bearings and 2 seals....may go with that. Lifetime guarantee.

kenfain Experienced

kenfain

Posted
Posted

I'd probably go with the cheaper set as well.  After all, these things don't really get much mileage.  Or high speed either.  So it'd be good for a few years at least. 

  • Like 1
Travis Grand Master

Travis

Posted
  • Author
Posted

I was able to find the pivot works kit on Amazon for 32.99....I'll take it over Kawasaki's $25 per bearing.

Expect a detailed write up on it soon! And I found something on the Mule I've never seen before..... 

Travis Grand Master

Travis

Posted
  • Author
Posted

I found 2 grease zerks I never knew it had,... They are On the front end, back side of where the tie rod comes from the steering, and it lubes  the shaft that pivots the spindle and wheel to turn it.... And they are in the hardest place to see.,  Never mentioned in the owners or Service manual.

 

 

wheel bearings are supposed to be delivered this Saturday. 

15886871148921686793058.jpg

rmissildine Contributor

rmissildine

Posted
Posted

That is a hard place to see. Now I'll have to check my 550. Once I get this animal running again I'm gonna check everything. Haven't really done anything except oil and filter changes since I've owned it. 

Take care,

Roger

  • Like 1
Travis Grand Master

Travis

Posted
  • Author
Posted

i used PIVOT WORKS  part number,  PWFWK-K36-000

Okay, first step.....

 Remove the wheel.... 4 lug nuts. then jack the front end up and support it with jackstands and chock the rear wheels.

remove the axle nut mud cover.

get a 1 1/6" socket to remove the axle nut... Don't forget to remove the cotter pin! you can use a breaker bar or impact to remove it.

there is a spacer behind the axle nut, remove it also.

now pull the drum off. sometimes it can be stuck on so spray some penetrating fluid between it and the backing plate, and tap it with a hammer while spinning it . you may have to use a 3 leg puller.

1767943675_IMG_20200506_1102081.thumb.jpg.03288b96896cc7899a589d968d5746a5.jpg

718329364_IMG_20200506_1106231.thumb.jpg.6c50981efafc0f628d7b07e1119f4ade.jpg

Now that the drum/hub assembly is off, this is what you should see.   the drum houses the bearings. there are 2 bearings, 1 spacer and 1 seal. the seal goes on the back of the drum, facing the brakes. the spacer goes in between the 2 bearings.

759261675_IMG_20200506_1109481.thumb.jpg.42fec304d533a7dcf931133a5e62ef7e.jpg

Now, my manual and also my common sense told me to PRESS  the bearings out. You CAN NOT press them OUT. there are 2 ridges that control the depth at which they are installed and you CAN NOT press them out.. you must use a slide hammer puller.

and you have to do it 1 bearing at at a time. Don't worry, the spacer is supposed to move freely in the drum.

I used the 3rd biggest puller attachment in the set.1766953717_IMG_20200506_1116451.thumb.jpg.d1fae08b06bc944c197573e8d9723f16.jpg

now that you have the old ones out clean the bore out with parts cleaner and a clean rag, and do the same to the spindle shaft on the mule., time to install the new ones!!! i recommend putting them in the freezer for about 30 minutes or more for ease of installation. they go in easier when cold.

i used a flat piece of wood to drive them in straight and then a 13/16" socket to drive them into the ridge, they are about 3/8" below the surface.

remember to do one bearing, install the spacer, then the other bearing, then the seal. the oil seal goes on the back side of the drum that goes against the backing plate on the mule. I recommend lubricating the seal lips and outer edge when installing into the drum assembly.468929302_IMG_20200506_1258321.thumb.jpg.53c8010d29f6dfb82c66d49e253783a6.jpg

1368258951_IMG_20200506_1311511.thumb.jpg.17e7294dc8c427f7f4ea02a0b66a05e7.jpg

now that the bearings are in time to Reinstall the drum!

just slide it back over the spindle shaft until fully seated... install the axle nut spacer, axle nut and cotter pin. before you install the cotter pin, torque the axle nut to 110 ft lbs.  reinstall the dust cap, tire, and lug nuts. lug nuts are torqued to 25 ft lbs, remove jackstands, let jack down, un chock the rear wheel. YOU ARE READY TO GO!

966346239_IMG_20200506_1318581.thumb.jpg.4ddf132112a2e38cb21684ea909a5ae8.jpg

 

 

  • Like 1
rmissildine Contributor

rmissildine

Posted
Posted

Travis, very good pictures and tutorial. However I am wondering about one thing. With the hub off, is there no clearance at all to get a drift inside and knock the bearings out??  Good point about putting them in the freezer before installing, I usually leave mine for a couple of hours though, really helps. You must not have a small shop press, mine is over 30 years old, but it really works well for pressing in bearings and seals.  I hope I don't have to do that job anytime soon!!!

Roger

Travis Grand Master

Travis

Posted
  • Author
Posted

oh ,we've got a 20 ton press, but you might could get a drift in their to knock them out... didnt think of that!

Can't press them out due to the ridges they bottom out on. once the first one was out of the way the 2nd was easy peasy.

 

 

  • 2 years later...
Penn Newbie

Penn

Posted
Posted

Travis,

Thanks for this.  I just finished this job on my 2001 mule 550.  Regarding the bearing removal:  If your bearings are in bad shape, skip the slide hammer and just punch them out with a hammer & screwdriver.  The slide hammer may be futile if the bearings are trashed and stuck like mine were.  For replacing the new bearings, O'reilly, Napa and Autozone  loan out a "Bearing race and seal driver set," which works great.    https://www.oreillyauto.com/detail/c/evertough/rental-tools-evertough-bearing-race-and-seal-driver-set/ren1/67034/v/a/18312/automotive-truck-2005-chevrolet-silverado-2500-hd?q=loaner&pos=7

Easy job other than getting those old bearings out.

  • Like 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Karlibob
      2020 Tracker 800 sx front end noise
      By Karlibob
      I have a 2020 800 sx with about 16 hours on it.  From day one I have heard a clunking noise from the front end going over bumps.  Has anyone else experienced this?  Also this past weekend while out riding I heard a noise that sounded like the dump bed bounced three or four different times, again has anyone experienced anything like that.  Thanks, gary
    • Hunterman22
      2021 Hisun Axis 500 No Start - Need Help Please
      By Hunterman22
      2021 Hisun Axis 500 UTV (From Lowes)
      Will NOT START
      MY apologies if this is to much info just wanted to give yal the most information possible for help.
      I'm a so called diyer. An Electrician by trade 21yrs. I got my S×S from my last job. The contractor purchased this S×S for this specific job brand new, from Lowes. They used it for hauling materials, tools, & a little bit of anything you can think of on an Industrial type job site. 
      I remember getting on the SxS one time & pushed the gas petal all the way to the floor & SxS had very little power. 
      So anyway ,when the job finished up back mid July this year (7/2024) , I asked the contractor what they was going to do with it. I was told to take it. Otherwise it would go to the contractors yard (storage yard) & most likely rust away. 
      Took it home washed it , it had a heavy coat of dust on it & in it dust was every where. My helper & I had to push it on the trailer to get it home.  After washing it throughly I let it sit & dry out for a good day and half, maybe 2 days. Before trying to start it. NO START. Will turn over & try to start but thats it. 
      So here's what I've purchased & installed. New Air Filter, new spark plug, new air idle control valve (AICV), new throttle position sensor, new throttle body, new oxygen sensor, new digital dash speedometer/fuel gauge/clock. 
      Also drained the old oil & gas & replaced with new oil & 93oct. gas. I should probably mention that I've changed the AICV twice. The 1st time I changed the AICV I was able to get the SxS started & let idle for at least 10-15min. Drove out of the garage, with very little power,  turned it around & barely got it back in the garage.That was the one & only time I've been able to start the SxS. I've also cleaned the Throttle Body and & intake with TB cleaner.  So after that the AICV was  making weird noise so I pulled it out & tried cleaning it, pretty sure I messed it up. So I purchased a Throttle Body that came with new AICV & TPS. Still NO START.  I've checked the fuel pump & the fuel injector.  I took the injector off still hooked up to wiring & turned the key over, the injector sprayed a lot of gas out kinda the size of a volleyball. I've also checked the clearance gap on the intake & exhaust valve. But today 11/2/2024 I'm going recheck spark plug gap & the valve gaps. And alot of other checking. Would the driver side seat belt have anything to do with it not starting?? I know the driver side seat belt has to be in gauged for full throttle "going fast". Thing is the drv. side seat belt will latch but feels like might be messed up inside of it. Tired opening it up but to no avail.  I've never had a S×S or 4wheeler so I was really excited when I got the S×S,not so much anymore.  I work on & fix my own vehicles usually no problems.  But this SxS is kicking my ass.
      So if possible & someone could help me with some ideas or tell me what Im doing wrong or did wrong, I would greatly appreciate it.  Thank you for reading thus far.
       
       
    • Blair
      Major Cabin Intake Noise Reduction
      By Blair
      Most of us complain about the ridiculous noise in the cabin. My wife likes to ride but the noise is a major downer. You can’t even have a conversation without shouting at each other. Well, I manage to reduce the cabin noise by approx 200%!

      I addressed the intake that is poorly placed right between the driver and passenger. First, I cut the air filter inlet pipe in half (pic 1). I then reinstalled it upside down (pic 2). I then attached a flexible intake tube (pic 3) and directed it behind the cabin (pic 4). Major difference.
       
      Then I covered the interior engine cover with Dynamat extreme and then 200 mil Chaogang sound deadener / heat shield mat on top of that (pic 5). Since I cut off the intake and redirected it, I completely closed off the intake (engine fence) so no engine noise can come thru (pic 6). It also reduced the heat approx 50%. I did leave on the heat mat that came stock on the engine cover, so it has 3 different mats. It was a snug fit. Major difference again.

      My wife rides all the time now since we can have a conversation when we ride. Major improvement to my riding experience. Thought you might like to check it out.


















    • TjB
      2510 Kawasaki mule Diesel
      By TjB
      My dad has recently acquired a 2510 Kawasaki mule Diesel powered. It worked fine  few weeks and then quit driving. Put a new belt on just to see. Still not driving. It already had a new clutch. Belt turns when in drive or reverse and back wheels are off ground to test. But wheels not turning. Thoughts? 
    • rsar
      Kawasaki Mule Cab Eclosure
      By rsar
      So I finally got my Quad Gear cab enclosure after waiting out the backorder for three months and to say it's been a huge disappointment is a pretty big understatement. I think mostly because I could make it work, if not for one major issue. The windshield is right next to impossible to see out of. It's a real headscratcher because the side and rear windows are okay. It's not high quality 30 or 40 gauge marine vinyl but I have Quad Gear's stand-alone winshield so I knew it wasn't the best in terms of visibility, but definitely doable for the price.  Incredibly, the side and rear windows of the cab eclosure are just as clear as the stand-alone windshield. And the windshield on the enclosure is like 50 percent worse than the stand-alone. It's the same company! I don't get it. If it had just been the rear windshield that was that bad I would have kept it. There are some creases and wrinkles here and there, but I've been using the stand-alone  windshield for the past three months so it's good enough not to have to shell out $600 plus for the stock hard windshield. I'd put visibility at about 65- 70 percent. The wife hates it though, which is a pretty big negative. In any case, my original plans were to have an upholsterer change the crappy vinyl out for the high quality stuff and I even sent it to a guy who ended up flaking out on me and refusing to do it. He said he didn't want to charge me $400 for something I paid $200 for.  Long story, short, I decided to return it and just get the insanely expensive Kawasaki enclosure next winter since the frigid temps here are about to start climbing in a couple weeks anyway. I first put it on just to see how it would look (I took pics of course) and found that it didnt even seal 100 percent and made it drafty inside the cab. So make that two major issues. At least with the stock enclosure everything will be top flight. Doors will be nice too.




UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...