Quantcast
Jump to content


Recommended Posts

Posted

I need help and idea's on the best options for a water tank/spray rig for a Mule Pro 6 passenger, used in the 3 passenger mode.  This will be for support of prescribed burns, once called controlled burns, to clear under brush and slash after logging operations and wildfire prevention.   Occasionally used to apply fertilizer, insecticide or herbicide on pasture.   Also to provide supplemental water for crops, gardens/landscaping.  Ideally it would be about 50 gal, with both a  boom and hand held sprayer,  and with a high volume pump.  It would be nice to be able to suction pump to load the  tank from surface water.

There are a lot of dealers, brands and units to choose from but I hope to hear from those that have some real world experience with this.

Posted

Sounds like you have a small scale operation.  50 gallons isn't much water especially if the prescribed burn gets too large..  A high volume pump might empty your 50 gal tank in a few minutes.  If you want to call a 5 gpm pump high volume, your tank would empty in 10 minutes.  I set up a similar rig to spray weed killer.  I used a 50 gallon blue barrel and a high pressure well pump.  Sprayig for weeds isn't the same as spraying for fires or watering crops even in a garden.  Just my opinion.

Posted

To Dan B, Travis,

Yes, pretty small scale,  we would not likely burn more than 25 to 50 acres at a time.  I would be one of several units with tanks, but if it gets out of hand we would be totally ineffective to help.  Mostly what I am looking for is for mop-up of dead trees, logs, trash, etc that continue to burn and could cause a later problem.  Also, maybe as Travis thought, a tow rig's added capacity would likely offset any issues of maneuverability and provide a little more effectiveness.   All of these burns would be under the control and guidance of professional burn management. 

Cost will rear its ugly head and the blue barrel and drop in pump may look really good.

Guys your thoughts and reply are appreciated.

Posted

Travis,  I have not seen one of these, but Wow they have it all, but yes pricey.  I have seen copycat units used by Forrest Service and Game Department personnel, I did not ask if they were personal equipment or owned by their departments.  I can see that the smaller more affordable (?) unit drafting from a couple of blue barrels on a trailer would be within the Mule's specs and should be highly effective.

I would like the drafting feature due to concerns about clearing/cleaning the tank and pump rig when switching from herbicide to say garden watering.  It would be easier to use a separate tank exclusively for herbicide.

Thanks it was fun to look at this and a great option if I can stand the price. 

  • Like 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Xov
      Just received delivery of a 2024 AMP Pro.  Thought I'd start a thread with my impressions as I use it and learn more.  There doesn't seem to be a whole lot of real-world usage information out there on this model.  Hope this will help others as they research.
      Intended Use Cases
      Fire mitigation / slash removal from a 5 acre forested and well-gamble-oaked property.  The previous owners thought as much about fire mitigation as I do about fashion: not much. Snow removal Stump pulling General hauling (rock, lumber, etc.) Weimaraner energy depletion.  Wasn't an original use case, but a nice added bonus.  Experiences So Far
      Wasn't impressed that two of the bumpers on the underside of the bed where it sits upon the frame were missing.  The metal on metal contact has damaged the powder coating and the frame.  I expect a little better QC.
      I've only put a few hours on it, so not a ton to report on usage.  It isn't quiet; it's silent.  I can't even detect an electric note from the motor. I removed (and subsequently replaced) the motor cover noticed that the motor is German and made by Schambuller.  The motor controller is Italian and made by Dana TM4.  Given the operating specs of both I found on the web, I suspect both are higher quality than the previous Navitas (which is supposed to be decent).  The motor is rated at 25 hp and 71.5 lb-ft of torque.  It feels very powerful.  All the torque is delivered instantly, if desired.
      The bed is huge and has an electric dump as standard.  Great feature but would like it to go up a bit more.  Probably not feasible from an engineering perspective, but I want and I need ;).
      Power steering is nice, but vague.  Probably common to many UTVs, but I am accustomed to more direct results from input.  Plan early and plan often.
      In our first full day of usage, we hauled about 1/2 as much slash as the entire rest of the year when I was doing it by hand cart.  I may get fatter, but I'll also get more done.  After a few days of usage, the battery meter has gone down by 1/10th. 
      Until next time...


    • By Prepper
      I have been doing a little research on which engine oil is best for UTV engines.  There seems to be some disagreement over using a good quality regular engine oil, and the necessity of using "M2" (or wet clutch suitable) oil.  My understanding is the "wet clutch" suitable oil has less friction reduction properties (hence a more responsive clutch with less slippage).  While less friction reduction properties would seem to be better for the wet clutch... it would not be best for the internal engine parts like camshaft bearings and other moving parts where friction is detrimental and would lead to premature failure.  Some folks swear you need M2 oil, while others say they have been using regular motor oil for years and their clutch is just fine.  Could they both be right ???
      Any thoughts ?
       
    • By Wolfpaak
      I think this part is causing a high idle problem(4000 rpm at start up) in my 04 R4 Joyner. I took it out and cleaned it and the problem went away. I just went out to start my SXS and it's idle jumped up to 4 grand again. Can someone tell me what this part is called so I can search for a new one. Or can you point me towards a source. 
      Thanks in advance. 
      Kenny


    • By Jon Spruill
      Hey Guys, I have been chasing a stalling condition for about two weeks now. The bike will crank up and idle fine, then after about 20 seconds it will fall on its face and stall. It happens at both idle and while running at various rpms. You can turn the key off, turn it back on and it will fire right back up without trouble. I have verified spark on both cylinders with a spark tester. I have also added an inline fuel filter, and pulled the injectors to verify proper pulse on each. Things I have replaced - (relearn procedure performed after each component replaced): spark plugs, ECU, relay/fuse box, fuel pump, & throttle position sensor - all with no improvement of the condition. The only warning light I get when the condition occurs is the oil lamp. The bike only has 14 miles. I am at a loss and appreciate any help and suggestions! Thanks
    • By Hunterman22
      2021 Hisun Axis 500 UTV (From Lowes)
      Will NOT START
      MY apologies if this is to much info just wanted to give yal the most information possible for help.
      I'm a so called diyer. An Electrician by trade 21yrs. I got my S×S from my last job. The contractor purchased this S×S for this specific job brand new, from Lowes. They used it for hauling materials, tools, & a little bit of anything you can think of on an Industrial type job site. 
      I remember getting on the SxS one time & pushed the gas petal all the way to the floor & SxS had very little power. 
      So anyway ,when the job finished up back mid July this year (7/2024) , I asked the contractor what they was going to do with it. I was told to take it. Otherwise it would go to the contractors yard (storage yard) & most likely rust away. 
      Took it home washed it , it had a heavy coat of dust on it & in it dust was every where. My helper & I had to push it on the trailer to get it home.  After washing it throughly I let it sit & dry out for a good day and half, maybe 2 days. Before trying to start it. NO START. Will turn over & try to start but thats it. 
      So here's what I've purchased & installed. New Air Filter, new spark plug, new air idle control valve (AICV), new throttle position sensor, new throttle body, new oxygen sensor, new digital dash speedometer/fuel gauge/clock. 
      Also drained the old oil & gas & replaced with new oil & 93oct. gas. I should probably mention that I've changed the AICV twice. The 1st time I changed the AICV I was able to get the SxS started & let idle for at least 10-15min. Drove out of the garage, with very little power,  turned it around & barely got it back in the garage.That was the one & only time I've been able to start the SxS. I've also cleaned the Throttle Body and & intake with TB cleaner.  So after that the AICV was  making weird noise so I pulled it out & tried cleaning it, pretty sure I messed it up. So I purchased a Throttle Body that came with new AICV & TPS. Still NO START.  I've checked the fuel pump & the fuel injector.  I took the injector off still hooked up to wiring & turned the key over, the injector sprayed a lot of gas out kinda the size of a volleyball. I've also checked the clearance gap on the intake & exhaust valve. But today 11/2/2024 I'm going recheck spark plug gap & the valve gaps. And alot of other checking. Would the driver side seat belt have anything to do with it not starting?? I know the driver side seat belt has to be in gauged for full throttle "going fast". Thing is the drv. side seat belt will latch but feels like might be messed up inside of it. Tired opening it up but to no avail.  I've never had a S×S or 4wheeler so I was really excited when I got the S×S,not so much anymore.  I work on & fix my own vehicles usually no problems.  But this SxS is kicking my ass.
      So if possible & someone could help me with some ideas or tell me what Im doing wrong or did wrong, I would greatly appreciate it.  Thank you for reading thus far.
       
       
×
×
  • Create New...