2021 White Mountain UTV Jamboree Aug 18-22
-
Popular Now
-
-
Similar Topics
-
By Alien10
My 2021 Coleman Outfitter 550 has a rear hitch receiver. It works OK for my towing of junk around the property BUT it is NOT welded directly to the frame of the SxS. Instead it fits into a sloppy tube and is pinned in there by a 5/8" hitch pin. This allows the receiver itself to wobble around to a small degree which can be annoying in some circumstances especially if towing and backing a trailer, it can droop or sway side to side by an inch or two at the ball. . I cannot figure out why they set up the hitch in this way, and am considering welding the tube directly to the frame as found in most hitch arrangements.
Has anyone else found this annoying and welded the tube up to the frame? If so, where there any down side to doing so? (Broken frame etc. ??)
-
By Tommy2bits
Just bought a brand new 2022 (NOS) Sector E1 with Lithium upgrade. (Single 135ah/200amp continuous). I've climbed a moderate hill in my woods probably 20 times since buying it. Today It won't climb it unless I am in Low. In High it almost makes it and then completely dies and I have to roll back down the hill. In Mid range (Max Range) I can't get 2 feet up the hill and the power output in only 100 amps, I have climbed this hill in every speed before many times. I put it on the trailer tonight and it wouldn't even get on the dang trailer in mid range. Torque is gone. That being said, when I am just cruising around in Midrange, it runs absolutely perfect with plenty of power. The only thing I did was charge it up, that is all. I charged to 100% using the charger that came with the battery. Before you think the BMS is shutting down due to overcharge protection, remember I am going UP hill so there is no regeneration AND I have done it before at 100% charge AND another big problem is that after 1 mile it is already down to 85% so it's not over charging and why is the battery draining so fast when I got 27 miles before. Battery output is fine in Low it pulls 200 amp up the hill just like normal so that doesn't point to the battery being the issue. All the individual cells on the battery are in line, so there is no dead cell either. I am tech savvy but to toward electric motors and I tried to cover all my bases. Please don't tell me basics like torque is reduced in High and Mid. The only thing I can think of is that I smelled something when I took my first drive today and I thought it was the Ebrake dragging but there was the correct amount of play in the cable and I jacked up the rear wheels and they spin freely. maybe something burned out in the motor, I do not knowm still runs great, we'll see if I have any trouble on the hills at the lake house this weekend. Maybe this is "Normal" and the settings were off before and was giving equal torque for whatever reason instead of 50% in Mid and 70% in High like the manual says....
For reference....this is it not even able to get on the trailer in mid range
-
-
By Travis
you're sick of chinese Crap but really can't afford the good OEM part?
Starter on the mule, i finally replaced the old D&B electrical starter (on august 28th) on it that was at least 5 years old with probably a million starts on it and apparently D&B no longer makes it/sells it, so i bought a $53 starter from CHYNA on amazon.. on august 19th, well here it is barely 1.5 months later, it clicks several times before it will spin over, all connections were good and i tested the key switch, and trigger wire voltage as well as the starter relay according to the service manual and they all check out. usually a tap with a hammer or if i turn the key back and forth fast several times it will kick in and start. would it be worth my time to remove the starter and lube it??
I've got the Denso and Kawasaki part numbers but boy... $$$$$$$$$$$$$$$$$$$
even a Reman denso is $230.
does anyone know of a decent aftermarket starter maker that might have one?
i've 12.5 volts at the big cable, and i get the same at the trigger wire as the manual states, but when its in F or R i get no voltage at the trigger, so i know the Neutral safety is working properly.
and if anyone can find one the DB starter was 190-542 18450
-
By Red Good
I have a massimo 500 with a blown motor and want rid of the rest of it . Is that ok here ? Motor is in a box , has low hours on the machine be a good parts machine for someone or stick a different motor in it . Tires are good body looks like no use on it . 500 bucks takes it away . 918-479-4200 located in NE Oklahoma . Red
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.