Quantcast
Jump to content


Recommended Posts

Posted

Moving to upstate NY (just south of Albany).

We will have a 1/4 mile gravel drive.  I have a 1/2 ton truck that I could use but rather not .  Could the Mule SX do this job with the plow accessory?  The dealer is on the fence, as am I.  Is the Mule SX 4x4 got enough power to deal with a 6-8" inch wet snow? 

Any experience with the SX and plowing snow?

Posted

It would probably be pretty tasking for it, however if you put it in 4 wheel drive it ought to handle it,  when we had our puny 4" snow here in Texas back in Feb. my old mule, with 2 wheel drive did great in the snow pulling 200 pound Adults (kids, lol) behind it on a piece of ply board.

Posted

I did use chains for one year but most times I just had a bed full of firewood to help with traction.  I would take care a big drifts a little at a time with the plow angled away and if the snow was really deep I would keep the plow about 3-4" above ground for the first pass.  My 2019 Pro MX has less issues as it weighs 500 pounds more on its own with an extra 4 inches of ground clearance but it also needs a 6 foot plow just to clear the wheel tracks when the plow is fully angled

  • 5 months later...
Posted

Brent what did you decide to do?
Like you I have a long driveway (1 mile gravel) to get to where the country maintains the road (they do a good job and are quick to start post snow storm).

I'm waiting on a Mule to arrive at the dealer (promised this month or next). First thing I will buy for the Mule since it is intended as a taxi from our house to the gate

are four of these:

https://www.amazon.com/dp/B017AHMCWO/?coliid=I7N58TVUG5Z2D&colid=2UAFGTQ7WPXRT&ref_=lv_ov_lig_dp_it&th=1

We do get big snows (2 foot plus) but those are rare. What is common is ice, ice so bad, so thick, so long lasting (only 3 days in the last 3 weeks above freezing here) that 

there have been two times in the last 3 weeks where I didn't even risk the 4Runner and it has studded snow tires.

So the dealer is pushing me towards a snow plow. He says the Mule SX is powerful enough but slow. He also said to start early in the snow storm, to knock off 2-4 inches at a time

and not wait until 12 inches have piled up.

From what I've read about those chains the Mule SX shouldn't have a problem at all on ice. I'm still mulling over the snow plowing with the Mule thinking like you've been mulling over

that the SX is a bit small, that the blade size needed to get both tire tracks when angled is too big for the SX.

I know with gravel we can't get the road perfectly clean, but when it does melt (and thank God that snow and ice can evaporate even from a solid form/sublimation point) it does slowly dissapear

even when we have (frequent) long periods below freezing.

Right now, having just taken the plunge into Mule SX world, I'm more worried about the plug fouling I've read about here in cold temps.

Can we not put an oil pan heater on the SX?

On my 4Runner I have heater in the block and an oil pan heater.....for when it doesn't get above 10F for days on end.

Posted
3 hours ago, MedicineMan4040 said:

Brent what did you decide to do?

 

Hi... well I could not wait for the Mule order and took delivery of a Uforce 800.  I installed  a belly mount, push tube, and 72" Mouse blade.  The Uforce 800 has plenty of power but when there is a lot of snow to plow (12") it does start to struggle (takes 3/4 throttle to keep speed up on my ~8% grade hill).  With that fact I think the Mule SW would not have worked due power avail.  I think for the Mule my guess is you need to take smaller bites and not let the snow pile up, maybe in my case would have maxed it out at 6-8".  So bang for the buck I'm happy how this worked out with my CF Moto, has the power (more available) and cost was same.  Time will tell on durability, but so far I'm impressed.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Popular Now

  • Similar Topics

    • By rdc
      Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]
    • By MilSurpYinzer
      Hey all, I was just wondering what you guys consider a necessary upgrade or spare part to have or mod onto your machine.
      I'm going for a kind of shtf survival rig that's not going to be SUPER heavy and I'm looking at getting:
      A spare belt (I keep seeing this mentioned everywhere I look so it must be important)
      A spare tire and mount( So would I need a jack like one from an old jeep or something else?)
      Tire chains for the winter
      And maybe a cargo bed upgrade so things don't slide out.
      Bumpers because duh.
      I already installed high output lights and have a windshield, roof, back window, and winch. And I outfitted a Molle panel for the back of my passenger seat with extra supplies like food, first aid, and spare mags.
      Any advise on increasing durability, longevity, and having something on hand because it's absolutely necessary would be a plus.
      Thanks so much!
    • By KMP
      We just bought our 1st side-by-side and wanted to get tips on maintenance items we should address immediately for our 2015 Arctic Cat Wildcat Sport 700 XT.  We are truly beginners and welcome any and all suggestions.  Thank you, we appreciate your help!
    • By Andy Dickerson
      So heard the grinding noise on the drive shaft a couple of times while going down a steep hill. Never heard this before going down the same hill. I already knew about the splines wearing out because of improper heat treating so I went through the process of removing the shaft to just replace it. A lot things need to be removed to get that thing out. Once I had it remove I didn't see any wear on the splines but what I did notice was the rear spline to rear differential had ZERO grease i.e. it was completely dry and I could see rust that had developed on the shaft splines and inside the differential mating surface. The front of the shaft where it connects to the transmission was well greased. Both ends of the shafts have springs in them with the rear spring being multiple times heavier which would force the shaft to mate securely into the transmission. Unless of course the rear is rusted and starts sticking which is what I think was happening. If the rear splines begin to rust and it starts sticking and the spring doesn't have the enough force to overcome the sticking because of the rust, the shaft will not get fully seated into the transmission. If this starts happening frequently it will eventually eat up the front splines on the transmission side shaft splines which is exactly what I see in the pictures of stripped splines. 
      I don't know why the rear spline shaft wasn't greased but this would cause it to eventually stick. I have been concerned about this ever since reading about it so as soon as I heard the grinding I stopped driving it. Thankfully there wasn't any wear. I'm wondering if this was deliberate or just laziness by the assemblers. It makes no sense not to grease it. The repair manual that I purchased from motorcycle doctor specifies to grease the splines. Both shaft ends have a rubber seal meaning there's is supposed to be grease in there. 
      I used to have a gold wing and there is a special grease required for the rear drive differential which happens to be a spline shaft setup. They use a lithium grease with moly. I had purchased a couple of tube of Magnalube-gx that I never used as I sold the bike. The Hisun manual recommends using a lithium grease which doesn't have the additives of a lithium moly grease that is specialized for spline shafts. Per magnalube website. "Magnalube-GX, however, uses a proprietary matrix of advanced polymers, molybdenum disulfide, and PTFE, so it stays where you put it without getting pressed out, while also maintaining a low frictional drag."
      Anyway, long story short everything is back together and no noise. I would recommend those that haven't checked the grease in the splines on both ends to do so before the shaft get destroyed. Especially If you have heard grinding. Those rubber boots can be pulled back without having to take to many parts off. If you've been hearing grinding then there is probably significant wear already and time to replace the shaft and grease it properly.
×
×
  • Create New...