Quantcast
Jump to content

2008 Joyner Trooper T2 Spare Tire/Wheel

Mrusson

By Mrusson
in Joyner UTV SxS Forum

 Share

Recommended Posts

Mrusson Newbie

Mrusson

Posted
Posted

Hey gang,

    I am looking for a 14x6 wheel with a 4/115 bolt pattern with the 4+2 offset for my 2008 Trooper. I have always had a spare tire with my UTV's and I am struggling to find a steel wheel for use as a spare tire with this Trooper. Has anyone had any luck finding a plain steel wheel for use as a spare? My trooper uses the 14" allow wheels from the factory with 14x6 fronts and a 14x8 rears. I assume the 14x6 can be used front or rear as a spare. Thanks for any info you may have come across.

Link to comment
Share on other sites
mixfixdave Enthusiast

mixfixdave

Posted
Posted

Honda Civic and others use 4x114.3 and I have a 15” civic set that I use with my BFG AT street tires that fit fine.
Also have some 30x10x15 UTV tires on weld racing drag lites with the dual 4 lug pattern…guy I bought them from had them on a mustang, but the 4x114.3 holes fit my 2008 T4. I had to buy the shouldered lug nuts to fit those wheels, but the stock Honda wheels use the same lug nut seats as the factory trooper.

  • Like 1
Link to comment
Share on other sites
Mrusson Newbie

Mrusson

Posted
  • Author
Posted

Dave,

   That is a wealth of information! Thank you so much for the info. I love your BFG streeties setup. Very nice! I will locate me some civic wheels and see what I get put together. I'm sure I will be back with more stuff. Also, thanks for the images of your power steering. That is a great setup and it looks super simple.

Link to comment
Share on other sites
  • 3 weeks later...
  • 4 months later...
Dave Ramm Rookie

Dave Ramm

Posted
Posted
On 9/19/2021 at 6:47 PM, fettman1176 said:

I currently own 5 trooper T2's and have extra wheels. Are you anywhere close to Arizona?

Five T2s ? You are a man that must really appreciate the uniqueness of these things. You must also have a wealth of knowledge about the machine as well. Do you happen to know what the back-spacing is on the original wheels like he posted the picture of, both the 14x6 and 14x8? I have searched high and low trying to unearth that information. 

Link to comment
Share on other sites
Dave Ramm Rookie

Dave Ramm

Posted
Posted
On 9/2/2021 at 11:55 AM, Mrusson said:

Hey gang,

    I am looking for a 14x6 wheel with a 4/115 bolt pattern with the 4+2 offset for my 2008 Trooper. I have always had a spare tire with my UTV's and I am struggling to find a steel wheel for use as a spare tire with this Trooper. Has anyone had any luck finding a plain steel wheel for use as a spare? My trooper uses the 14" allow wheels from the factory with 14x6 fronts and a 14x8 rears. I assume the 14x6 can be used front or rear as a spare. Thanks for any info you may have come across.

Well now I look like an idiot, totally missed your posting the offset for the 14x6.  I'd like to find out what the offset is on the 14x8 and the maximum  inside offset is you can run on the front before tie rod interference. I want to compile a list of other machines that have wheels that we can use/ interchange. It would be a good reference when you see used wheel tire packages for a different machine at a sweet price. It's always nice to be able to have a couple different sets of tires and wheels on hand for different terrain. 

Link to comment
Share on other sites
  • 1 year later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Ron from the Mitten
      2008 Qlink Rodeo 700
      By Ron from the Mitten
      I purchased a 2008 Qlink Rodeo 700 a few years ago.  I am from Michigan.  Anyone know of any local repair shops?  I had a dead battery, so I replaced that, started right up, ran the quad down the road, (this was last year), put it in the barn, shut it off.  then a couple weeks later, went to go start it again, and nothing.  I have power to the dash lights, horn, turn signals, wench etc, but nothing to the starter switch, and I hate electrical crap.  Battery still reads 12.x volts.
       
      Any suggestions would be amazing.  I've owned it over 2 years, and haven't run 1 tank of gas through it.  No time to screw with it, and very frustrated.  Hoping someone can offer some advice of value.
    • alevins
      2008 HS700 reverse rev limiter
      By alevins
      Good day all, 
      searching here but cannot find the answer,  Hisun been working fine and now reverse limiter seems to be engaging and cannot back up, cannot find a clear solution to disable the limiter. found a possible relay?  not sure which one or to cuut a wire at ecu but a picture or diagram would be helpful
      thank you for any help in advance
    • MJG
      Looking to Purchase 2008 Joyner Renegade
      By MJG
      Hello, 
      I found an 08 Renegade for sale and looking to purchase it.  I haven’t heard too much about these machines and any insight would be much appreciated.  Are they good machines?
    • Amagi
      2008 arctic cat 700 xtx prowler No spark
      By Amagi
      Hi to all. I’m new on this forum and I need some help. I have a 2008 arctic cat 700 xtx prowler. I have no spark. 
      I have done the following repairs. 
      changed piston and cylinder 
      change CDI 
      change ignition coil and spark plug
      changed speed sensor
      changed stator and flywheel 
      Changed voltage regulator 
      after all this I still have no spark. 
      i have verified all fuses and they are all good. 
      please help. I would like to get it running. 
       
    • goindeep
      Trooper Fuse Diagram????
      By goindeep
      Well now i could use a lil help... i have a trooper in my shop now that has wiring issues... this poor guy paid another shop $1000 to re wire the body control harness, and boy oh boy did they chop it up!!! I am Buillding a new harness from scratch... what i need is a diagram that tells me what each fuse and relay control on the Engine fuse/relay block.. any help is greatly appreciated!!
      Josh
      No Limitz

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...