Quantcast
Jump to content


GPS Power Pickup/Hood Removal Fix

Gumball

By Gumball
in Joyner UTV SxS Forum

 Share

Recommended Posts

Gumball Collaborator

Gumball

Posted
Posted

I finally took the hood off my Trooper today - boy was that fun. I'm looking for a good power source for my GPS. With all the expert help on this forum I figured someone will have a good answer to this question. Any thoughts will be appreciated.

To avoid the need for 6 foot long arms to get to the nuts under the hood I went to ACE Hardware and bought some UNM-L6 U nuts. They slide right over the frame brackets that should have had the 10mm nuts tacked to them. That solved the problem of trying to hold the nuts with one hand while trying to loosen the screws with the other. Being a new guy, others probably did this long ago but I thought I'd share anyhow.

Gumball

brostar Proficient

brostar

Posted
Posted

Gumball, this problem has been discussed before but your solution is better than I remember. That is a good idea and one I'll take on board.

By the way, welcome to UTV Boards and after reading your profile, I know you are going to be another valuable member.

Cheers Mike.

Kinarfi Veteran

Kinarfi

Posted
Posted
I finally took the hood off my Trooper today - boy was that fun. I'm looking for a good power source for my GPS. With all the expert help on this forum I figured someone will have a good answer to this question. Any thoughts will be appreciated.

To avoid the need for 6 foot long arms to get to the nuts under the hood I went to ACE Hardware and bought some UNM-L6 U nuts. They slide right over the frame brackets that should have had the 10mm nuts tacked to them. That solved the problem of trying to hold the nuts with one hand while trying to loosen the screws with the other. Being a new guy, others probably did this long ago but I thought I'd share anyhow.

Gumball

Gumball, what GPS do you have and what are the power requirements?

If you're going to start replace 10 mm nuts with UNM-L6 U, may I suggest 95210A175 METRIC TAPPED-HOLE U-STYLE CLIP-ON NUT, M6 X 1 MM PITCH, FOR .34 - 4 MM THICK PANEL @ $7.33/PK of 25 from http://www.mcmaster.com/# and also do the under side which probably has the nuts down and subject to damage, making them a real bitch to get undone. You also might consider hinging your hood, another thread.

Kinarfi

Gumball Collaborator

Gumball

Posted
  • Author
Posted

Thank you for the good information. ACE charged me $1.15 a piece for the nuts. Your place, McMaster-Carr charged me about $.30 a piece plus shipping. Quite a savings. I bought enough to do my whole car and my buddies car.

Thanks again,

Gumball

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Popular Now

  • Similar Topics

    • rdc
      Looking for the left side shaft carrier where the rear bearings go for a 2014 1100cc sand viper, I understand an 800 cc carrier will also work.
      By rdc
      I posted this before , but I had the year wrong. The part I need is for a 2014, I don't know what all years will work, but I need the 2 bearing style with the spacer in the middle. It looks like this pic. If anyone has one I'll buy it rite away. my email is [email protected]. Thanks, RC

    • rdc
      Looking for a left rear shaft carrier (just the carrier) for a 2007 Joyner 1100 sand viper
      By rdc
      Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]
    • Mitch13
      Coleman 400 wiring help
      By Mitch13
      2022 Coleman 400 with 13 hours on the engine and the mice got to it. Every wire coming out of the steering column in one cluster has been eaten through. I tried reconnecting matching wire colors to each other and I get the left turn signal and hazards to work, nothing else. If I play around a bit I can get the horn to honk or headlights to come on but only when I connect them to the brown wire. Obviously I don't know what I am doing here. Does anyone have a picture of how these wires are connected when they are under the hood on the drivers side coming from the steering column?
      Gray - seems to carry power
      Brown - left turn signal
      Green with purple stripe - hazards?
      Pink with red stripe - horn?
      Green - head lights?
      Yellow - head lights?
      Yellow with red stripe?
      Blue?
      Dark green?
      There is also a bundle hanging under the hood not connected to anything green with yellow strip, brown and blue?
      Other than that issue, I am about ready to sell this for parts if you interested let me know.
      Thanks
    • Rmillerdesigns
      Massimo Msu 500 Has No Power
      By Rmillerdesigns
      Hello. I have a 2016 Massimo MSU 500. I was putting on a lightbar and i screwed up and didn't disconnect the battery so when i was taking of the positive cable to put on the power from the lightbar it sparked and now the utv has no power. I turn the key over and all i hear is a chirp. No lights or anything. Everything that comes from the battery to the jumper box up by the battery shows voltage but anything coming out does not such as to the winch or anything like that
    • MilSurpYinzer
      Must have upgrades/spares?
      By MilSurpYinzer
      Hey all, I was just wondering what you guys consider a necessary upgrade or spare part to have or mod onto your machine.
      I'm going for a kind of shtf survival rig that's not going to be SUPER heavy and I'm looking at getting:
      A spare belt (I keep seeing this mentioned everywhere I look so it must be important)
      A spare tire and mount( So would I need a jack like one from an old jeep or something else?)
      Tire chains for the winter
      And maybe a cargo bed upgrade so things don't slide out.
      Bumpers because duh.
      I already installed high output lights and have a windshield, roof, back window, and winch. And I outfitted a Molle panel for the back of my passenger seat with extra supplies like food, first aid, and spare mags.
      Any advise on increasing durability, longevity, and having something on hand because it's absolutely necessary would be a plus.
      Thanks so much!

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...