Quantcast
Jump to content

BMS Stallion 600 freewheel going downhill


Phil

Recommended Posts

  • Alex changed the title to BMS Stallion 600 freewheel going downhill

Thanks Kenfain for your input. When I first got the UTV it didn’t freewheel, but has since started to. I know Polaris and other UTV’s freewheel and that is normal for them. Yes, hitting the gas does re-engage the clutch. Perhaps the freewheeling is normal, I just don’t want to damage it more if I have an issue 

Link to comment
Share on other sites

Could be that as yours has aged, it has loosened up a bit. As long as you can still activate it, in a consistent way. I wouldn't worry about it unless that changes. 

If it starts to act up, like failing to kick in, even when prompted. Or if it feels like an unsafe condition results. Then you might have an issue. 

Link to comment
Share on other sites

My cfmoto Uforce 600 had the wet clutch go out. Before the clutch went out the engine brake worked just fine. I got a replacement wet clutch, clutch drum, engine brake, etc from Amazon and not official cfmoto parts.

 

After putting everything back together with the new engine brake. Mine acted just as you have described. Most of the time it would engage. There were times it would not. But hitting the gas would raise RPMs and then the engine brake would engage. 

 

In the 6 months mine has been doing this. It hasn't hurt anything. Maybe caused a little more brake pad wear when engine brake wasn't engaged but that is about it.

But I don't ride in extreme situations very often with the wife.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Alien10
      I have a Coleman Outfitter 550 purchased in January 2022 that runs and operates pretty well.  65 hours on it so far.   It is a work vehicle for my 10 hilly acres with two 1 acre woods and 5 acres of "lawn".  The rest is under a lake. 
      My parking brake does not seem to have any grip.  It worked when new but after a month or so, it is just almost useless.     I press the parking brake pedal hard until it stops. Still, it won't hold even on slight inclines.   I don't see the caliper move as I press the brake pedal down.  There seems to be plenty of pad left on it and the rotor is shiny as if it is rubbing a little when applied, but not enough to stop it from rolling. 
      Any thoughts on possible causes? 
       
    • By Onebad54
      Has anyone solved the 750 Hisun Sector shifter problem?
    • By skittle021
      So I've got a Hisun 550 that I was doing some work on that required removing the CVT and it's housing. Upon attempting to reinstall the clutch, sheaves, etc, I found that the belt no longer fits - it's far too wide. None of the parts have been replaced, they're all OEM. Exactly the same parts as what I took off a few weeks ago.
      To be more specific, my belt is 1.25in wide, but the gap between the clutch and the primary sheave is only 7/8in wide. I'll include a few photos to explain.
      Has anyone ever experienced such a bizarre problem? Any help at all would be appreciated, I've been stuck on this for a month. I'm open to just about any suggestion.
      Photos: 
       





    • By Robert B
      Going down a 20 deg hill engine is holding UTV back. Then something releases like going into Neutral and makes a loud clacking noise. Have to use brake to slow UTV down. Then once level it shifts back into gear. Have done shift extension does not pop out of gear.
    • By JFC
      I have a  3500LB Winch that only runs in one direction.  Inward but not Out.  Replaced the solenoid module.  Makes "click" when I push the "Out" button and the motor tries to spool out but then stops and begins to "click".   Does anyone have suggestions what I should try next?       
×
×
  • Create New...