Quantcast
Jump to content

Tracker 800SX Windshield Frost


Recommended Posts

Thanks, Travis. I was born and raised in Dallas where I only saw snow once. Now I live in NW Wisconsin where we already have about a foot of snow on the ground and a low tonight of -21. Our Tracker windshield ices over inside from our breath when we’re snow plowing for 8 hours and it’s hard to see, so I’ll try the alcohol wipe to see how it works. Maybe I’ll carry a bottle of Jim Beam to see how that works! I’m sure after an hour I won’t care! Seriously, thanks for the tip, I’ll try it tomorrow.

  • Haha 1
Link to comment
Share on other sites

I think the current configuration has the fan on the right side of the engine blow across the cylinder head and exhaust to assist in cooling. After that I think the air goes via a tube directly downwards. Is there a way to duct this air to the windshield?

You can also look for a defroster for the old air-cooled VWs. Back in the 60s and 70s we used to add these little 12v units to help defrost the windshield. A word or caution, as this may be more of a load than the stock stator can support, so if you go this route, I would add a 12v battery under the driver's seat, and power the defroster from that, You can charge the battery while you are not driving the Tracker.

Here's a link to the type of defroster/fan unit I am referring to:

https://smile.amazon.com/QUUREN-Portable-Windshield-Defroster-Demister/dp/B09FDP55ZT/ref=sr_1_4?crid=2BL8P5W2SI68X&keywords=12v+defroster+for+car+windshield&qid=1641556750&sprefix=12v+defros%2Caps%2C175&sr=8-4

 

Link to comment
Share on other sites

2015 mule......i run a portable generator in the bed when plowing, with a small electric heater in the cab for warmth.....to keep the windshield from fogging,  i have a small 12 volt fan that directs air to the windshield.........that keeps fog at bay....for the exterior, i have no windshield wiper so i carry a squeegee to keep it clean....been using this method for several years, works like a charm......... 

Link to comment
Share on other sites

  • 2 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By aefron88
      I've seen a number of requests for the location of all the grease points on these machines, and there is no definitive list in the manual. This covers the UT400, but other Coleman/Hisun models should be similar.
      Tools:
      First to grease your machine you need a grease gun and some NLGI#2 grease. You will find it helpful to buy a needle attachment as pictured here, due to poor clearance on some of the U-joints. The rest of the zerks use the standard attachment.
       
      Technique:
      Wipe any dirt/grease off the zerk before greasing to prevent pushing gunk inside and causing excess wear.
      Push the grease gun on the zerk at a straight angle and give it a few pumps. You will hear an oozing noise or sea grease coming out from the outside of the greased area when you've put enough grease in, a few pumps should be plenty.
      If it's just oozing around the zerk you either don't have a good seat with the gun, or the zerk may be rusted and the check ball frozen. Try seating it again and regrease.
      Wipe up any excess grease when youre done to prevent making a mess.
      Greasepoints:



      Rear A-Arms are greasable with the wheels on from the rear, I took the picture with the wheel off for easier visibility

       
      That's it. All other Hisuns should be substantially similar.
    • By REDfletching
      Spent today at a Honda dealership looking at their 520 side by side, then on the way home past our Lowes noticed they had several new UTVs on site, so we U-turned and ducked in there. We were impressed that all that came for $9,999 metal whole length skid plate, nice sized bed, roof, windshield, side mirrors, winch, upgrade looking tires… all of which would have added thousands of dollars to an already expensive Honda 520. Now Honda does have a great reputation from my trusted UTV experienced buddy, so it has that going for it.
    • By packersfan
      I have a hisun 500 got from a auction and when turning a corner left or right it's a two hand job then when you left go snaps back.any help on what to look at would be appreciated.
      Also blows blue smoke until she gets warm then it's ok 
    • By Bassarino51
      My 2014 Odes with less than 1000 miles suddenly won’t turn over with a fully charged battery.
    • By didgeridoo
      Hello, All!  I've decided to replace the traction batteries in my 2018 Sector E1 with a 48V Lithium set. They may be expensive, but I figure the Discovery Dry Cell are, too. I am not looking for the max driving range, as I have never received near the brochured range to begin with, but a good mix of charge/ get work done/ charge is what I am expecting.
      I have settled on the 48V EAGL kit from bigbattery dot com. Each battery pack provides 30Ah. The kit ships with a charger, as well. The packs would be physically connected in parallel (using a busbar) to one another, maintaining the 48V voltage, but together would be able to provide the amp draw the buggy pulls when going up hill or towing a rake (rated 320 max continuous Amps). This is in comparison to the serial connection the eight 6V lead batteries. Each of the EAGL batteries looks to have its own BMS; am I correct in thinking I will have to use their included charger rather than (simply) changing the onboard charger to lithium mode? The chemistry of the pack is LiFe PO4, for what it's worth.  I haven't torn anything apart yet (to diagram), so  I am not sure how the dash will interpret the AMP draw, but the kit I am looking at includes a dash mounted charge indicator.
      If anyone has completed a similar conversion, do you have any tips? Specifically, how did you remove the original batteries, and how did you secure the new ones? I am guessing that almost any change from the stock batteries would involve at least some modifications. Any tips would be appreciated, especially things I may have failed to consider. Thanks!
×
×
  • Create New...