Quantcast
Jump to content


Recommended Posts

Posted

How HOT? What do you mean you can hear it? Bubbles moving in the coolant or air exiting thu the head gasket? Have you taken/check with your dealer? Is your coolant level dropping requiring to be topped off? Any moisture coming from the exhaust? Did you get the engine really hot? This is the same engine as in the Trooper and this is not normal, IMHO. No other persons have report this problem. If you haven't taken it back to your dealer, do so quickly. I would guess a blown head gasket. Run a compression test & a pressure test on the cooling system!

rocmoc n AZ/Mexico

Posted

The head gasket is fine.

I pulled out the thermostat

If I am on it hard for a few miles the red overtemp light comes on and the gauge needle is all the way to the right.

It will cool down pretty quick if I stop and keep the engine running

It never overflows in to the expansion tank

16psi cap

If I pull up the red tab on the cap it will flow in to the expansion tank and I can see air bubbles

I can hear air coming through the hose going to the radiator from the head.

the coolant level does go down slightly when the air comes out.

I figure all of the air will work its way out sooner or later but I was wondering if there is a quicker way.

Posted

Go for a small run or medium rev the engine for 30 seconds to warm the engine up a bit and then take the radiator cap off. Leave it to idle and heat up more so the thermostat opens up. If the coolant level drops your in business just keep on topping up at the radiator not the overflow bottle. When the level stops dropping put the cap on and go for a decent blast for say 10 minutes or so turn off & leave to cool then check again and top up if needed. If the coolant level fails to drop at all back at stage one then this is not going to work. I've only done this before on a car as per my mechanics advice & it worked fine. Good luck.

Cheers Mike.

Posted

After it warms up and you take the cap off, run your engine up to 1000-1500 RPM and top it off up at that RPM. When it doesn't need anymore put the cap back on and then let it idle. Check to see if any runs into Tank.

Posted

Jack up the rear of your machine as high as you can. This will place your radiator at the highest point. Do what the others have suggested, may help! I had to do this with one of my past race cars to get all the air out. I would still let the dealer know about your problem. You could also call Joyner in AZ.

rocmoc n AZ/Mexico

Posted

There is pond dam near my house that is pretty steep

I will try letting it sit on the side of that for awhile over the weekend.

I guess I could just try doing a long ride in the hills

that would the fun way

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By rdc
      I have a 2007 Joyner 1100 sand viper and  before it even get's to where the thermostat opens up the oil pressure get's so low I have to shut it down. What could fix this ? I thought about adding an oil cooler with fan, thicker oil, or removing the thermostat. Any advice?
    • By OBL
      program will open in old Bud program only/ but will not go in BUDS 2 to let use program ECU problem working on has new engine/ new fuel pump/ injectors/ lines/ sensors/ crank sensor maps/ and new throttle body and injectors. machine starts runs a minute dies/ on 3 rd  try says key not recognized /we put other key in and same thing happens/wait 10 minutes, you can go again/ is there a back door in the program/ also might mention unplug temp sensor and map sensor , it will run a few minutes longer / then die again.
    • By AaronD1982
      Onto the next problem, everything has been replaced in the charging system except the Flywheel Rotor, I have it torn apart all the way down to said rotor, but it is suggested that a specific puller is required, and a compatible rotor seems virtually impossible to find.  I can find many like it, but this one is mine scenario for those that get the reference.  For all I know I have the last Massimo Buck 400S on the planet and will never find another part again, but who knows.  Any ideas, help or otherwise that anyone might have would be greatly appreciated.
    • By Fmaxiron
      Hit a rock last weekend and trashed my front A-arm and axle on my Outlander. I’ve been looking around for reliable sources for replacement components. A lot of listings online look a bit hit or miss, so I’m trying to figure out what’s actually worth trusting.
      Has anyone here had good luck with dealers or sites where you can buy genuine Can-Am spare parts online without worrying about quality issues or fake OEM stuff? I’d rather pay a bit more and get the right fit than deal with problems later.
      Any recommendations appreciated.
    • By rdc
      I posted this before , but I had the year wrong. The part I need is for a 2014, I don't know what all years will work, but I need the 2 bearing style with the spacer in the middle. It looks like this pic. If anyone has one I'll buy it rite away. my email is [email protected]. Thanks, RC

×
×
  • Create New...