Warrior 700 owner, Thibodaux Louisiana .
-
Similar Topics
-
By CYJSP2009
Dear Friends
Supply Hisun cables and Hisun parts.
We have Hisun cables stock in South Carolina.
Please send email to [email protected] for inquirying and further discussion.
Thanks
Casey/ Leaf Asia
2023-09-15
-
By TomW
I was driving the UTV the other day when it simply died. I was using the sprayer which might have drained the 3 year old battery and the stator didn't recharge it. I towed it to my shop and charged the battery . The next morning it cranked first time and I drove it home . I parked it and turned it off . I then tried to crank it and it would only make a weak click noise . I changed the battery and the voltage regulator but it would still only click. I noticed on the digital display that the reverse light was illuminated and would stay illuminated no matter what gear I selected . If I put it in low that light would light but the reverse light stayed on . Same thing for neutral . I shorted the two poles on the starter solenoid with the key on and it cranked up easily and idled fine. You could put it in reverse and it would move backwards and you could put it in low and it would drive forward. The entire time the reverse light stayed on . I checked the fuses and they all looked good . So lets say I get a new started solenoid . If I replace it and it now starts with the key what is the issue with the reverse light . Is it harmful? What else needs to be done to correct ? Any ideas out there.
-
By Bryan g
We see a lot of the UT400 with shift problems, not going into gear, popping out of gear, grinding etc. There is a bulletin Im sure everyone has saw about adjusting shift cable. That dont always fix it. I went round n round with coleman on couple units. We are a Coleman warranty repair center"AFS Small Engine Repair " I told them shift lever does not have enough travel . No amount of cable adjustment will increase travel . I extended lever with piece on flat iron by 3/4 of inch . This gave shifter enough travel to properly engage into gear completely . Last couple units to come in for this Coleman sent me a modified shift lever, with longer travel . Problem solved! Also , heads up if you get any new unit ,,,go over and check it out, grease all zerks, check air filter for being in backwards, check wiring harnesses for rubbing on rotating parts, brake hose routing , make sure not touching exhaust . These are just few of the more common failures I see .
-
By Kierobi
New to owning a UTV and got myself a project one as my first one.
Changed out the clutch and clutch housing etc. as the UTV was having problems going up hills and getting up to speed but now in the process of putting it all back together it won't start. Also changed fan gears for shifter
Here's what I've found so far (apologies for the bullet points);
Motor will crank over and makes good turnover speed. If I use spark plug tester or ground to engine, no spark. At the connector to the ignition coil I get consistent 12v on the white wire and nothing at the black. Read in one of the posts that the 12v to the white wire should be intermittent when trying to get a spark at the plug? Tested ignition coil using a multimeter on resistance setting. Between two pins I get 0.46 ohms or thereabouts. Between either pin and spark plug boot I get somewhere around 16k ohms. Not really found a good video on testing these coils but think those are good readings. Checked fuses in fuse box and are all good. Fuel pump cycles on when I turn key to on position. I disconnected the ignition coil to remove the clutch etc. to get it out the way but don't think I've damaged anything in the process. Can anyone point me in the direction of what to try next? Been trying to use the manual but considering the test procedure for the ignition coil is for the wrong type of coil, it's not been too helpful. I've read on another post about checking the ECM the two pins with 12v etc so will take a look at that next but any ideas that could get this machine started again are welcome!
-
By JimB
I have a 2014 Massimo HS 500 that has the Headlight/turn signal kit installed. When operating the turn signals the light up but do not blink, the hazards do the same. I cannot locate the flasher. Any help appreciated!
-
-
-
Similar Tagged Content
-
- 6 replies
- 647 views
-
MSU 500 Won't shift into Low, but works great on Hi and Reverse
By Chris M,
- low gear only
- msu500
- (and 4 more)
- 2 replies
- 686 views
-
- 3 replies
- 2,010 views
-
- 22 replies
- 4,873 views
-
- 0 comments
- 1,566 views
-
-
Gallery Images
-
-
-
By cmotosales1, -
-
-
By islander83, -
-
By Travis, -
By cmotosales1, -
By plumber, -
-
-
By BeeZee62, -
By ricksrb, -
By ChrisG, -
-
-
-
-
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.