Quantcast
Jump to content

2021 Massimo T-Boss 550 fuel supply issue

JDSmith

By JDSmith
in Massimo UTV SxS Forum

 Share

Recommended Posts

JDSmith Rookie

JDSmith

Posted
Posted

I have a 2021 Massimo T-Boss 550. It was submerged in water for a period (hurricane). All filters/fluids were drained and replaced/refilled immediately after as well as air box cleaned. Drained fuel tank, popped the supply line off and key cycled to clear the line of contamination. Reconnected line and filled with fresh fuel. The machine fired and sputtered for maybe 30 seconds and died. Upon attempting restart I noted the fuel pump wasn’t priming.  I checked voltage at the pump and it is 12v. I’ve replaced the coil pack, wire, ecu, ignition (which was failing just prior to the water event) and the fuel pump. The new pump still does not engage. Rechecked with new pump and there is 12v at the plug on top of the tank as well as down at the pump. I’ve popped apart all the plugs I can see, sprayed them with terminal cleaner and applied dielectric grease. Still nothing. I’ve talked to a buddy and he has said it has to be a connection or ground issue.  Anyone able to point me to specific plugs wires etc to check? I’m paying for the answer. 😂 

Link to comment
Share on other sites
  • Alex changed the title to 2021 Massimo T-Boss 550 fuel supply issue
JDSmith Rookie

JDSmith

Posted
  • Author
Posted

I will have to look for that relay. From what I can see I believe my fuel pump relay is a little different.  I don’t have a relay checked for this type, but I wasn’t thinking it was the issue as I can feel the click in the relay when key is cycled. No more than they cost and it’s not like I haven’t thrown $400-500 at it already I should just try it I suppose.

7A901247-E954-451F-8294-50BD6677DDA1.jpeg

Link to comment
Share on other sites
  • 2 weeks later...
JDSmith Rookie

JDSmith

Posted
  • Author
Posted

Tank was drained and refilled. Purged line and reconnected. Started and ran for about 15 sec before dying. Noticed at that time the fuel pump wasn’t priming anymore. 
 

I’ve also replaced the fuel pump. So unless the original and then the new replacement was bad, it’s not the pump.

Link to comment
Share on other sites
  • 5 weeks later...
  • 1 month later...
Greg Kilgore Collaborator

Greg Kilgore

Posted
Posted

I know its an older post. But I agree that it seems like it is a ground issue. If the original poster would post his resolution that would help.

But some info on relays and power. And if I wrong it won't be the first time.

The relay should supply the positive 12V DC power. To whatever. The ground or negative side should go to a frame ground or back to the battery.

Frame grounds are a lot of problems on many many electrical issues on a lot of vehicles. Whether it's a side by side or a 2001 GMC Sierra dash cluster (don't ask) or a 1997 Dodge Dakota dash cluster (ground point under the kick panel on driver and passenger side).

Cleaning the ground points or running a ground wire back to the battery should resolve the issue. If the fuel pump and relay is good.  

But usually there are many circuits feeding off one ground point. So it would be best to follow the ground coming off the fuel pump to make sure the ground point is making good contact to frame. 

The ground wire can be tested with a multi-meter.

1. Set multi-meter to OHMS.

2. Hold one lead of multi-meter to the other lead of multi-meter. The reading should be 0.0 to maybe 0.2. That will be the reference of the meter and also tells you there is little to no resistance between the leads.

3. Now take the negative side of the fuel pump wire to one lead of the multi-meter. and touch the other lead to a UNPAINTED part of the frame. The reading should be the same or maybe 0.1 more than when you touch the leads of the meter together. 

If no reading or a very high reading that would indicate a bad connection to ground somewhere and the ground point would need to be cleaned.

 

Hope this info helps you or someone. I'm not responsible if anything unwanted happens while you're testing.

 

Link to comment
Share on other sites
JDSmith Rookie

JDSmith

Posted
  • Author
Posted
3 hours ago, Greg Kilgore said:

I know its an older post. But I agree that it seems like it is a ground issue. If the original poster would post his resolution that would help.

But some info on relays and power. And if I wrong it won't be the first time.

The relay should supply the positive 12V DC power. To whatever. The ground or negative side should go to a frame ground or back to the battery.

Frame grounds are a lot of problems on many many electrical issues on a lot of vehicles. Whether it's a side by side or a 2001 GMC Sierra dash cluster (don't ask) or a 1997 Dodge Dakota dash cluster (ground point under the kick panel on driver and passenger side).

Cleaning the ground points or running a ground wire back to the battery should resolve the issue. If the fuel pump and relay is good.  

But usually there are many circuits feeding off one ground point. So it would be best to follow the ground coming off the fuel pump to make sure the ground point is making good contact to frame. 

The ground wire can be tested with a multi-meter.

1. Set multi-meter to OHMS.

2. Hold one lead of multi-meter to the other lead of multi-meter. The reading should be 0.0 to maybe 0.2. That will be the reference of the meter and also tells you there is little to no resistance between the leads.

3. Now take the negative side of the fuel pump wire to one lead of the multi-meter. and touch the other lead to a UNPAINTED part of the frame. The reading should be the same or maybe 0.1 more than when you touch the leads of the meter together. 

If no reading or a very high reading that would indicate a bad connection to ground somewhere and the ground point would need to be cleaned.

 

Hope this info helps you or someone. I'm not responsible if anything unwanted happens while you're testing.

 

 

Link to comment
Share on other sites
JDSmith Rookie

JDSmith

Posted
  • Author
Posted

Well we just got it back running…

it was the fuel relay and ecu. Turns out the new ecu was bad as well. A dealer was able to pull a working one off a new unit and it all worked. 
 

the new issue when you put it in reverse it defuels and dies now. The speed sensor is allegedly a common issue, replaced it and same thing. So we just had to leave the speed sensor unplugged and it’s fine. Dealer said Massimo said the causes would be ECU, Speed sensor, or the dash. I’m not replacing the dash so it is just no speedometer for me.

Link to comment
Share on other sites
Greg Kilgore Collaborator

Greg Kilgore

Posted
Posted

Glad you got your machine back running. Hopefully the ECU was covered since it was DOA.

I'd guess that since the machine was submerged for a minute or two. There may be more electrical issues pop-up from bad sensors. 

At least the resale value should be higher since your not racking up miles.😁

You may have more relays go in and out or ground issues in the coming future. 

Could an app and cell phone for speed if needed.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Smittay
      Massimo durability and parts
      By Smittay
      (posted a similar question to the Hisun folks) Looked at a lot of UTVs lately. Couple Questions about Massimo. Some people say they are just cheap with no customer service. Other people seem to have no problems with them.
      Any opinions on Massimo durability?
      Heard parts might hard to get. Is that true?
      What models are the best?
      If you had one and didn't like it what do you recommend? 
    • buckrub
      trying to finish assembly "new" 2021 Coleman ut 400
      By buckrub
      Hey guys! Newbie here. I'm an old man who's better with plowing a mule (4-legged kind) than these newfangled beasts. I, and a friend of mine, just bought new Coleman sxs and are having to finish the assembly. I've been reading on this site and I'm falling on the mercy of you experts. The only way I'm an expert is that an "ex" is a has been, and a spurt is a drip under pressure. LOL First off, the 2 buggies have no ignition switches. They seem to mount on the dash, not the opening in the steering wheel shaft cover, so we ordered new ones that are supposed to fit. They are 8 inches long, and have a 4-wired white plugin which is slightly rectangled when looking at the end of the plug. The trouble is there's nothing to plug into. There is a three-wire grey plug close enough to reach the four-wire plug, but of course, they are not compatible. 
      Secondly, the blinker, light, ect. unit on steering wheel just spins around when touched. I see no way in heaven or earth to secure it. I've looked at a diagram on the Powersports site, but can't detect how it mounted. Fellows I'd be so grateful for any help with this. Me and my mule will even plow your garden for free, for your help. LOL 
       
    • AlaskaTrail
      2021 Coleman UT400 - Transmission fluid change
      By AlaskaTrail
      Hi All,
      New to UTVs and recently accuired a ut400 from our local Alaska Commercial Co. and had a questions regarding the transmission fluid. I have had a squeeling noise, sounds like a teapot, that recently started after being driven for a few minutes. The manual says to change the fluid at 500 miles, so I was thinking maybe its just time for this to be changed. Other then that I cannot find any information regarding the type used. While reading through these forums, I seen someone put that the transmission is lubricated with the engine oil. Is this true? If not what should I be using and where can I find the information to change it out? Any input on this would be greatly appretiated!
      Thanks in advance
    • Nathon S.
      Bennche 700 EFI Bighorn New Fuel pump not working
      By Nathon S.
      I have a Bennche 700 EFI Bighorn. I’ve recently been unable to get it to start. After a little troubleshooting I realized my fuel pump was not pumping fuel. This weekend I emptied the gas and replaced it with new. I replaced the fuel pump, fuel filter and fuel injector. I also replaced the battery, spark plug and made sure all my fuses and relays were good. I have confirmed that the float on the fuel pump is not obstructed. The UTV is about 12 years old and has less than 100 hours on it. It has not run in over a year.  Not sure whats going on?!? After doing a little reading I'm leaning towards it being an issue with the ECU or perhaps a faulty wire in the wiring harness. Anyone have any ideas on where to start looking or what I could be dealing with? Any help is appreciated, thanks in advance!
    • Hugh
      2018 Hisun Sector Crew 1000 engine die after about 15 minutes run
      By Hugh
      My 2018 Hisun sector crew engine cut off after about 15 minutes run. There is no indicator of what is wrong, no error code just die and won't restart until it cool down. I notice that the fan is not running but the temp indicator is on low temp, no overheat indicator. I checked the radiator fluid, it is cool to touch.
      Cooling fans are working, I can hear it running once awhile if I can get the engine warm up enough.  Thank you for all the help.
       
      Hugh

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...