Quantcast
Jump to content

2018 Hisun Sector Crew 1000 engine die after about 15 minutes run

Hugh

By Hugh
in Hisun UTV SxS Forum

 Share
Go to solution Solved by Hugh,

Recommended Posts

Hugh Newbie

Hugh

Posted
Posted

My 2018 Hisun sector crew engine cut off after about 15 minutes run. There is no indicator of what is wrong, no error code just die and won't restart until it cool down. I notice that the fan is not running but the temp indicator is on low temp, no overheat indicator. I checked the radiator fluid, it is cool to touch.

Cooling fans are working, I can hear it running once awhile if I can get the engine warm up enough.  Thank you for all the help.

 

Hugh

Link to comment
Share on other sites
Jerry_Axis500 Newbie

Jerry_Axis500

Posted
Posted
On 3/11/2024 at 10:16 AM, Hugh said:

I have a AXIS that started to do the same thing after 100 hours (brand new). I use premium Ethanol Free fuel. It would die after 15 minutes and wouldn't start until it cooled off. I changed Fuel filter first and it wouldn't start at all after that. I changed spark plug after that and still will not start. Very frustrating. I'm in line to take it to have it serviced but this is frustrating with only 100 miles on it.

 

Link to comment
Share on other sites
  • 2 weeks later...
  • Solution
Hugh Newbie

Hugh

Posted
  • Author
  • Solution
Posted

Quick update on the issue and resolution.

I went ahead and replace the crankcase sensor along with both of the ignition coils. We took the UTV out for about an hour over the weekend without any stall. So I think the problem is fixed. 

Link to comment
Share on other sites
  • 3 weeks later...
Hugh Newbie

Hugh

Posted
  • Author
Posted

I wasn't able to verified for spark but it acted the same way. I read on car forum about the crank position sensor causing the same issue as what I seen on my UTV. Since the part is not that expensive and difficult to get to, I went ahead and replace them anyway. Once that replaced, everything work fine and the engine seem to be a little more responsive and less noisy as well. We took it out a few more times for couple trips over an hour ride at the time. No problem so far.

Link to comment
Share on other sites
Jerry_Axis500 Newbie

Jerry_Axis500

Posted
Posted

Follow up on my issue. I took it to a HISUN certified repair shop and it took these guys 3-4 hours of troubleshooting to figure out what was wrong because it was sporadic (I get it...if you can't get consistency with the issue and  recreate it, it is hard to diagnose). The issue with mine was an obvious QA issue from the manufacture (I only have 100 miles on it). The plug for the fuel injector power was not plugged in all the way so sometimes it worked and other times it didn't.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • didgeridoo
      Hisun Sector e1 Battery replacement: any tips?
      By didgeridoo
      Hello, All!  I've decided to replace the traction batteries in my 2018 Sector E1 with a 48V Lithium set. They may be expensive, but I figure the Discovery Dry Cell are, too. I am not looking for the max driving range, as I have never received near the brochured range to begin with, but a good mix of charge/ get work done/ charge is what I am expecting.
      I have settled on the 48V EAGL kit from bigbattery dot com. Each battery pack provides 30Ah. The kit ships with a charger, as well. The packs would be physically connected in parallel (using a busbar) to one another, maintaining the 48V voltage, but together would be able to provide the amp draw the buggy pulls when going up hill or towing a rake (rated 320 max continuous Amps). This is in comparison to the serial connection the eight 6V lead batteries. Each of the EAGL batteries looks to have its own BMS; am I correct in thinking I will have to use their included charger rather than (simply) changing the onboard charger to lithium mode? The chemistry of the pack is LiFe PO4, for what it's worth.  I haven't torn anything apart yet (to diagram), so  I am not sure how the dash will interpret the AMP draw, but the kit I am looking at includes a dash mounted charge indicator.
      If anyone has completed a similar conversion, do you have any tips? Specifically, how did you remove the original batteries, and how did you secure the new ones? I am guessing that almost any change from the stock batteries would involve at least some modifications. Any tips would be appreciated, especially things I may have failed to consider. Thanks!
    • great8redsfan
      2017 Challenger 500 No power on take off or hills
      By great8redsfan
      Okay folks. I have a low power issue. Been like this for a few years. Place I work at bought 3 and all have lost most of the pulling power.  They gave them away after local shop worked on one for 3 months and it had great power for about 1 month and then crap. They replaced throttle body, fuel injector, spark plug and IAC motor. Seat belt switches have wires cut and left open so no seat belt warning light anymore. It revs to 6k rpm in neutral but when put in gear and take off in low it just doesn’t seem to want to go anymore. Running 93 octane fuel with Stabil.  Any ideas greatly appreciated. I dont have a scan tool but no codes on dash. If held to floor it pops a little and runs almost 5K rpm but if I let off pedal about an inch it smoothed out and revs up to 6k rpm. 
    • htrotte
      2011 Massimo HS500UTV-EFI third temp switch?
      By htrotte
      #1   While troubleshooting an issue with temp warning light I discovered another temp switch mounted in the pipe going to the head  The two switches are literally 6 inches apart.  Does anyone know what this third switch is used for?  If i can figure out how I will post pictures.
      Author #2   Finally got the pictures took.  See the photo and tell me if you know what the switch on the right is.
      It looks to be factory and I know the girl who bought it new and she didn't install it.
      I can't find anything on it in any manual i have looked at.  Any help would be appreciated.

    • Joe Toup
      Fault Code Troubleshooting "How To"
      By Joe Toup
      Hey Folks
      There are not a lot of good sources out there for troubleshooting and diagnosing ECU problems with the Massimo Buck, Bennche Bighorn, Bennche Cowboy, & Cazador machines that use the Delphi MT05 ECU. They are all basically the same with different badging, so I thought I'd share some info that I found during some searches. I was trying to help someone diagnose and repair a hard starting issue.  The ignition coil was throwing a 0351 code.  I discovered how to read codes without an OBDII code reader.  The following procedures should help you check your fault codes and clear them if needed.
      Fault Code Troubleshooting for Delphi MT05 ECU on the Massimo Buck 400, Bennche Bighorn 400, Bennche Cowboy 400, and Cazador 400
      *NOTE: The MT05 ECU is not really OBD 2 compliant. It is much more similar to an OBDI system.  The MT05 ECU controls either 1 or 2 cylinder engines commonly found on Massimo, Bennche, and Cazador.
      Much of the ECU info was found here:
      https://netcult.ch/elmue/HUD ECU Hacker/Delphi MT05 Manual.pdf
      Delphi EFI System Design
      Delphi EFI employs 5 sensors to monitor engine performance.
      1. Crankshaft Position Sensor
      2. Coolant Temperature Sensor
      3. Oxygen Sensor
      4. Throttle Position Sensor
      5. Manifold Air Pressure/Manifold Air Temperature (MAP/MAT) Sensor
      Delphi EFI employs the following system components.
      1. MT05 Engine Control Unit (ECU)
      2. Fuel Pump
      3. Multec 3.5 Fuel Injector
      4. Idle Speed Control Valve (Idle Stepper Motor)
      5. Multec Ignition Coil
      6. Fuel Vapor Canister Purge Valve
      Using the Digital Dashboard to Decipher EFI Trouble Codes
      In addition to commercially available diagnostic scan tools (Big $$$), you can use the engine warning light of the Siemens dashboard to diagnose most of your EFI problems. The digital dashboard receives signals from the MT05 ECU, and the engine warning light will flash a diagnostic trouble code (DTC) if the ignition key is switched on/off for three cycles.
      When you turn on the ignition, the engine warning light will illuminate, which indicates the EFI system is operational. After the engine is started, the engine warning light will extinguish if the EFI system is working properly. However, if the engine warning light remains illuminated, it indicates the EFI system is not working properly, and there is a system component failure.
      Deciphering Diagnostic Trouble Codes
      To read the diagnostic trouble code (DTC), open and close the ignition key three times in rapid succession, as follows: open/close—open/close—open. At this point the engine warning light will flash a DTC which indicates the fault in the EFI system. Refer to the attached fault code table to identify the corresponding problem.
      The engine warning light will emit a sequence of flashing lights. If the light flashes 10 times, the translated number is 0. If the light flashes one time, the translated number is 1, et cetera.
      For example, if the MAP/MAT sensor is disconnected, or the connector is shorted to ground, the engine warning light will flash in the following manner (This is an example only).
      The engine warning light will flash 10 times: The first number of the DTC is 0
      After an interval of 1.2 seconds, the engine warning light will flash 1 time: The second number of the DTC is 1
      After an interval of 1.2 seconds, the engine warning light will flash 10 times: The third number of the DTC is 0
      After an interval of 1.2 seconds, the engine warning light will flash 7 times: The fourth number of the DTC is 7
      The resulting DTC is P0107.
      NOTE: For the system I was helping to troubleshoot, I suspected an ignition coil failure due to the code that was thrown.  When it was checked, it was flashing:  10, 3, 5, 1.  The 10 represents a 0.  So the actual code was 0351.  After finding the code, the coil wire was checked and discovered loose at the spark plug.  Once it was pushed fully on, the problem was fixed.  Most likely, this problem was created after the owner had pulled the spark plug to check the gap.  The ECU was rebooted using the procedures detailed below with no more codes being thrown.   
      If there are other fault codes, the engine warning light will flash the next code in 3.2 seconds after finishing the first sequence.  After all existing fault codes are flashed, the engine warning light will repeat the fault codes in a loop sequence, until the ignition key is turned off.
      To clear fault codes you either need an OBDII Fault Code reader and a Delphi 6 pin connector adapter cable that you have to order from China and wait 8 weeks…OR....you can simply reboot the ECU using the instructions detailed below.
      Rebooting the ECU
      Perform the following steps to reboot the ECU.
      1. Turn off the ignition for 15 seconds.
      2. Turn the ignition on/off for 5 cycles. Make sure each cycle lasts about ½ second, verifying the start of the fuel pump for each cycle. If the fuel pump doesn't start during any cycle, begin the entire reboot procedure from the beginning.
      3. Turn off the ignition for 15 seconds.
      TPS (throttle position sensor) re-learn procedure after rebooting ECU.
      This should be done after replacing the TPS or the ECU....and it is advisable to check proper idle after rebooting an ECU too.   Source: ECU Hacker (Reworded process slightly to make it a more sensible flow in my mind):    1. Turn the idle screw one full turn clockwise before starting   2. Start the engine, and run at low idle until the engine warms.  Maybe a couple of mins.   3. Idle should be above 1500 rpm. If it isn’t, turn it up to 1700 then shut the engine off.  Do another reboot of ECU.   4. Restart the engine and let it stabilize at 1700 rpm.  Then turn the idle screen down to 1500 rpm and let it stabilize for a few seconds.  Once it stabilizes, set to the final recommended idle speed for your machine. The placard under (or behind) your seat should show idle speed, valve adjustment, spark gap, etc.  Typically the 390 cc engines in the "400" machines run at 1600 rpm idle. 
        5. Shut it down. Wait 10-15 seconds before restarting.  The procedure is now complete.  Final Notes:
      I have included pictures of an OBDII connector and the Delphi 6 pin connector in case anyone wants to go buy stuff off ebay or local parts suppliers and build a connector to use for an OBDII reader. But...you can save money and simply do the same thing with code reading and resetting using the check engine light on your dash.  Some folks prefer to do it with code readers.  
      Hope the information provided helps if anyone ever needs it but cannot find it in repair manuals. I discovered most of this in some motorcycle forums.  The source for the diagrams is here:
      https://netcult.ch/elmue/HUD ECU Hacker/
      Be advised: I am not a service technician.  I do not endorse any manufacturers. I do not get paid to help, nor do I want to.  This is just a hobby of mine.  I enjoy working on things and solving problems.  If you run into a weird problem that stumps you, give me a shout.  I may be able to give you some ideas...or not.  Just know, that troubleshooting thru emails can be challenging.  The more info you can provide, the better.  Otherwise, I will probably ask you a ton of questions.  The good news is, the Delphi system used on these machines is essentially an OBDI and it is very simplistic.  If you are methodical and patient, most of your "problems" can be figured out thru a process of elimination.  Always go for the simple things first before throwing money and sensors at a machine.  
      Take care 
      - JT
       




       
    • Randyh79
      Hisun Sector 750 – dash light adjustment
      By Randyh79
      Is there a way to adjust the brightness of the dash light on aHisun 750 sector?

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...