Quantcast
Jump to content


Farmington buggy build

Jarrad

By Jarrad
in Joyner UTV SxS Forum

 Share

Recommended Posts

Jarrad Community Regular

Jarrad

Posted
Posted

We started the build for the farmington buggy yesterday making nice progress.. wheels are off to powdercoat, the cage is being shortened 4"'s chopped the lightbar installing mini Piaa lights, stereo, warn winch, tube fenders front and rear, rock sliders, I am using a 2008 T2 it's all we had left in stock 2 used buggies, but I went ahead and converted it from electrical 4X4 to namual lever

More photos to come!

Jarrad

DSCF0849.jpg

DSCF0848.jpg

DSCF0847.jpg

DSCF0846.jpg

DSCF0850.jpg

rocmoc Grand Master

rocmoc

Posted
Posted

I have the same aluminum top. I used diamond plate and turned the diamonds inside with the smooth side out like yours. I used a piece of aluminum flat and laid the lights down like a sun visor. I can remove two bolts and stand the lights up if I wish to use them. Have not be stood up in two years. MORE, MORE!

rocmoc n AZ/Mexico

Jarrad Community Regular

Jarrad

Posted
  • Author
Posted

Tomorrow we get down to the nitty gritty, we were running short on the 1.5" .080 wall DOM tubing, have 100 feet being delivered in the morning, we start on the tube doors in the morning that will swing open.. this is going to be something unlike you guys have seen before.. we also still have to build the new spare tire holder and add the rock sliders.. The passenger grab handle is almost finished and I finally found the face for my stereo set up.. we are cruising along nicely..

The buggy will get wrapped first of next week and we expect the wheels to be back this friday so I can get it back in rolling condition so much work and hardly enough time to do it all.. will be pushing the deadline pretty close with the wrap job suppossed to tgake a few days

Jarrad Community Regular

Jarrad

Posted
  • Author
Posted

I have the same aluminum top. I used diamond plate and turned the diamonds inside with the smooth side out like yours. I used a piece of aluminum flat and laid the lights down like a sun visor. I can remove two bolts and stand the lights up if I wish to use them. Have not be stood up in two years. MORE, MORE!

rocmoc n AZ/Mexico

The rock sliders are being built right now, I pick the wheels up first thing in the morning, need to install the stereo and build the spare tire mount next, put my new G-force seatbelts in and a few minor details then hopefully tomorrow afternoon I can get it to the wrap shop

Jarrad Community Regular

Jarrad

Posted
  • Author
Posted

How much to bring a set of the door mounts & door tubes to Farmington? I am sirius!

rocmoc n AZ/Mexico

Actually wait till you see it finished.. And someone bring thier checckbook.. I don't really want to haul it back home

Jarrad Community Regular

Jarrad

Posted
  • Author
Posted

How much to bring a set of the door mounts & door tubes to Farmington? I am sirius!

rocmoc n AZ/Mexico

Nearing the end wheels here today mounted tires and my guy Aurturo is building the back half and tire carrier

DSCF0864.jpg

DSCF0861.jpg

DSCF0863.jpg

DSCF0862.jpg

DSCF0865.jpg

Jarrad Community Regular

Jarrad

Posted
  • Author
Posted

I have the same aluminum top. I used diamond plate and turned the diamonds inside with the smooth side out like yours. I used a piece of aluminum flat and laid the lights down like a sun visor. I can remove two bolts and stand the lights up if I wish to use them. Have not be stood up in two years. MORE, MORE!

rocmoc n AZ/Mexico

Finished except for the wrap

DSCF0869.jpg

DSCF0868.jpg

DSCF0867.jpg

DSCF0866.jpg

DSCF0870.jpg

Jarrad Community Regular

Jarrad

Posted
  • Author
Posted

Looks real good.What did you use to mount the stereo ? was that a joyner item?

Thanks,

No it is something I whipped up quite awhile ago.. has been on 3 buggies, there are also rear speakers and a box but without the rear tire rack to mount them to I did not install

Guest Lenny

Guest Lenny

Posted
Posted

No it is something I whipped up quite awhile ago.. has been on 3 buggies, there are also rear speakers and a box but without the rear tire rack to mount them to I did not install

Nice job Jarred. Did you put the Renegade diff gears in it? Looking forward to Farmington.

Lenny

Jarrad Community Regular

Jarrad

Posted
  • Author
Posted

Nice job Jarred. Did you put the Renegade diff gears in it? Looking forward to Farmington.

Lenny

I have not yet.. took it to wrap this morning, depends on how long they take, will be deciding factor on the gear set, I had the choice between a little better crawl ratio or looking good.. looking good took the better part of my judgement for right now

brostar Proficient

brostar

Posted
Posted

It sort of reminds me of an old 10cc Song

I was walkin' down the street

Concentratin' on truckin' right

I heard a dark voice beside of me

And I looked round in a state of fright

I saw four faces one mad

A brother from the gutter

They looked me up and down a bit

And turned to each other

I don't like Jarrad's Trooper

I love it

I don't like UTVs

I love them

Don't like Farmington,

I love her (New Mexico Holiday)

To every one going, have a bloody good time. I reckon that old 10cc song would sound pretty good blasting out of your new stereo set-up Jarrad.

Cheers Mike.

ricksrb Mentor

ricksrb

Posted
Posted

I have not yet.. took it to wrap this morning, depends on how long they take, will be deciding factor on the gear set, I had the choice between a little better crawl ratio or looking good.. looking good took the better part of my judgement for right now

Are you going to post some pics when you get it back from being wraped? anxious to see it.

Jarrad Community Regular

Jarrad

Posted
  • Author
Posted

Are you going to post some pics when you get it back from being wraped? anxious to see it.

You bet I am I can't wait for tomorrow, not sure what time it will be though.. I need to call them and ask that question.. Still unsure it will fit in my enclosed trailer, may have to haul it on the flat-bed

Jarrad Community Regular

Jarrad

Posted
  • Author
Posted

Are you going to post some pics when you get it back from being wraped? anxious to see it.

They are telling me late tomorrow afternoon, But here is the last trooper they did for me so use your imagination on what it will look like, I am getting the same black and real flame job

2009 Joyner Trooper

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • rdc
      Looking for the left side shaft carrier where the rear bearings go for a 2014 1100cc sand viper, I understand an 800 cc carrier will also work.
      By rdc
      I posted this before , but I had the year wrong. The part I need is for a 2014, I don't know what all years will work, but I need the 2 bearing style with the spacer in the middle. It looks like this pic. If anyone has one I'll buy it rite away. my email is [email protected]. Thanks, RC

    • rdc
      Looking for a left rear shaft carrier (just the carrier) for a 2007 Joyner 1100 sand viper
      By rdc
      Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]
    • paul allen
      2016 wildcat tail front axle rubber boot
      By paul allen
      right front axle cv joint boot keeps getting torn up from the inside out....the stock one was damaged from a stick...i have replaced  the axle 4 times with aftermarket axles that fit fine..after 4-5 miles of riding even on grass.the outer boot get torn up from the inside out...all 4 brand new alxes...bearings are fine nothing bent everything fits just fine....nothing seems to be binding.....any thoughts?????
       
       
      thanks...pa
       
    • Sidewinder
      Polaris RZR 800 Rear Differential Pinion Nut Issue
      By Sidewinder
      All mid 2008 through 2014 Polaris RZR 800 series have a big problem with the rear differential pinion nut backing off, allowing the pinion gear to shoot into the rear differential, destroying the rear differential. This has happened with machines with as little as less than 100 miles on them! Reports indicate that there are no problems, nor warnings, until the rear differential grenades, locking the rear axles solid! This requires the machine to be lifted onto a trailer, to be transported for rear differential replacement, as it destroys the case. After failure, rear differential replacement can be quite expensive: labor alone can run from $800-$1200 and a new OEM Spicer rear diff, if you can find one, can run from $1700-$2500! So, if you own any Polaris RZR 800 series between the years of 2008-2014, I recommend that you do this repair before further use of your machine. personally, I have grounded my machine until it can be done. Please check the online post for your own awareness.

    • brewski
      installing light bar on kubota rtv 1100 x
      By brewski
      I just purchased a 2025 kubota rtv 1100 x cab esd esnting to install light bars on the roof it appears to be prewired for lights how do lights mount and what kind of switches do i need

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...