Quantcast
Jump to content


Oil pressure sending unit

jamesrulz

By jamesrulz
in Joyner UTV SxS Forum

 Share

Recommended Posts

jamesrulz Contributor

jamesrulz

Posted
Posted

Does anyone know an oil pressure sending unit that I can sub out instead of the factory one my second one is toast. I think an old style one off a 70's dodge would work but I can't compare resistance because mine is toast. Does anyone have any ideas or part numbers for something I can get at napa or a resistance spec?

renegade II Apprentice

renegade II

Posted
Posted

I did think of that but I think it's just one more line that will get ripped off or leak.

check the ground wire on the back of your oil pressure gage, if it's like mine there is a small fiber washer and it shuld be removed, after I removed them from all my gages they all worked like new and have had no problems after that.

rocmoc Grand Master

rocmoc

Posted
Posted

Also if you have removed the sending unit and reinstalled with Teflon tape, it most generally will not work. Remove the sending unit, remove the Teflon tape and reinstall with nothing on the treads.

rocmoc n AZ/Baja

Kinarfi Veteran

Kinarfi

Posted
Posted

Also if you have removed the sending unit and reinstalled with Teflon tape, it most generally will not work. Remove the sending unit, remove the Teflon tape and reinstall with nothing on the treads.

rocmoc n AZ/Baja

I think the heat shielding may be a very necessary thing also, I added some shielding around my headers because the plastic deck had warped from the heat and I was worried about my shocks getting hot from the exhaust and I also made sure the original heat shield stayed put on my oil pressure sender unit.

Kinarfi

rocmoc Grand Master

rocmoc

Posted
Posted

No problem. My new cage configuration has no deck of which I have not had time to work on. Hoping this will get rid of the some of the heat in the engine compartment. BUT I have never heard ever that heat was an issue with a oil pressure sending unit in anything! Remember it is already exposed to the heat of the engine block & the oil in the vane to the sending unit. Maybe the wiring to the sending unit!

rocmoc n AZ/Baja

Kinarfi Veteran

Kinarfi

Posted
Posted

I grounded the sensing wire and the gauge went to zero from pinned so it's the sensor. I Dont think it enjoys being close to the exhaust.

So is your sender working now and it was just the ground wire or is it still dead? as I reread, you grounded the sensor wire, right? can you measure any resistance from sender out put to ground terminal or case? and ground terminal to case?

kinarfi

  • 10 months later...
66fastcarss Contributor

66fastcarss

Posted
Posted

Just info for the next guy, but my oil pressure gauge also quick working out of the blue. After reading this post, I followed the advice given from Renegade and took off the red fibrous washers from the terminals on the back of the gauge (actually took off all 3) and it worked just fine again (until I ripped out out the wire from the connector due to a slip when plugging it back in :( ). Will get that connected back up and expect it will work just fine. Not really sure if it was just a bad connection or if those washers somehow cause problems, but it seems to be fixed now.

Kinarfi Veteran

Kinarfi

Posted
Posted

Just info for the next guy, but my oil pressure gauge also quick working out of the blue. After reading this post, I followed the advice given from Renegade and took off the red fibrous washers from the terminals on the back of the gauge (actually took off all 3) and it worked just fine again (until I ripped out out the wire from the connector due to a slip when plugging it back in :( ). Will get that connected back up and expect it will work just fine. Not really sure if it was just a bad connection or if those washers somehow cause problems, but it seems to be fixed now.

I over torqued mine and busted the terminal off, so I soldered a piece of wire to it and capped that end with silicone and use wire nuts, no problems since.

Kinarfi

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Popular Now

  • Similar Topics

    • rdc
      Looking for the left side shaft carrier where the rear bearings go for a 2014 1100cc sand viper, I understand an 800 cc carrier will also work.
      By rdc
      I posted this before , but I had the year wrong. The part I need is for a 2014, I don't know what all years will work, but I need the 2 bearing style with the spacer in the middle. It looks like this pic. If anyone has one I'll buy it rite away. my email is [email protected]. Thanks, RC

    • MilSurpYinzer
      Must have upgrades/spares?
      By MilSurpYinzer
      Hey all, I was just wondering what you guys consider a necessary upgrade or spare part to have or mod onto your machine.
      I'm going for a kind of shtf survival rig that's not going to be SUPER heavy and I'm looking at getting:
      A spare belt (I keep seeing this mentioned everywhere I look so it must be important)
      A spare tire and mount( So would I need a jack like one from an old jeep or something else?)
      Tire chains for the winter
      And maybe a cargo bed upgrade so things don't slide out.
      Bumpers because duh.
      I already installed high output lights and have a windshield, roof, back window, and winch. And I outfitted a Molle panel for the back of my passenger seat with extra supplies like food, first aid, and spare mags.
      Any advise on increasing durability, longevity, and having something on hand because it's absolutely necessary would be a plus.
      Thanks so much!
    • Timbo
      Does anyone take axis/hisun 500 to Hatfield trails?
      By Timbo
      I never see videos of hear of people taking these things to the big trails. Do you ? I just got one and want to.
       
    • Sharon
      The center console is not working, anyone know how to fix it?
      By Sharon
      The center console is not working, anyone know how to fix it? 
    • Outlaw Redneck
      How to make a commando transmission work in sand spider
      By Outlaw Redneck
      Hello all. I have a 2005 Joyner sand spider 650 with the dreaded broken output shaft on the transmission. I got ahold of a 2007 joyner commando 650 for cheap that had a bad motor but a good transmission. I got it because everything i read said that the transmission would work but it seems that it will not. Due to the commando being 4x4 it has a selectable locker and a small ring gear using a "idler" gear to turn the ring gear which make the output spin the wrong direction. Is there any way that I can make this thing work? I really dont want a commando,  I like the buggy but if the trans wont work then I can only put my motor in the commando. Any help would be appreciated. I have the ring gear from the original trans but the shaft is broken and the shaft from the commando wont fit the ring gear it doesn't appear. 

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...