Quantcast
Jump to content


JOYNER FORGED PISTONS

silverbullet

By silverbullet
in Joyner UTV SxS Forum

 Share

Recommended Posts

silverbullet Experienced

silverbullet

Posted
Posted

Silverbullet.

WE are working on a forged pistons for the TROOPER 1100 CC.WE are going to change the compresion ratio to 8.5 and have floating piston pins for turbo motors.You can raise the turbo pressure and get more power on pump gas to the wheels We are going to offer total seal rings.Or stock rings you can have a coated piston or not.We are going to offer stock compression ratio forged piston for the guys who wants to rebuild thear motor.We will try to keep the price down.We do not have cost price yet

jamesrulz Contributor

jamesrulz

Posted
Posted

Silverbullet.

WE are working on a forged pistons for the TROOPER 1100 CC.WE are going to change the compresion ratio to 8.5 and have floating piston pins for turbo motors.You can raise the turbo pressure and get more power on pump gas to the wheels We are going to offer total seal rings.Or stock rings you can have a coated piston or not.We are going to offer stock compression ratio forged piston for the guys who wants to rebuild thear motor.We will try to keep the price down.We do not have cost price yet

That's good news I was thinking of trying to find a company to build me some custom pistons. Let me know when you have some ready to go I would love to crank up my waste gate!

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Tim n Deb
      2015 Massimo stalled and wont start. oil, new plug, getting gas verified. cranks but does not start
      By Tim n Deb
      Riding out today it acted like it ran out of gas,  stalled and died and would not start.   Towed back to house,  New  plug added this past month,  plenty of oil, getting plenty of gas, battery cranks good.   Trys to kick in and starts but doesnt.   Two days prior while sitting at a idle it died.  Added gas and it started did my ranch chores with it.  But just now it stalled out cranks but will not start.   Tried to find if fault codes came up on the clock like manual says but not sure I am doing that right.  Any and all help apprecated.  Thank you
    • Chile
      Massimo MSU 700 Piston Clearance
      By Chile
      2018 Massimo MSU 700 EFI. I realize that this engine is essential the same as in all of the HISUN based Yamaha clones out there. I am in the process of performing a top end diagnosis/rebuild. I have an AMAZON top end rebuild kit on order in anticipation of this activity. 
      Question 1:  When exploring the myriad of top end rebuild kits on the market for these units there are some cylinder assemblies that have "686 cm3" badging next to the cam cain tensioner boss. Others compatible with the unit do not have this badging. The existing cylinder assy does not have the 686 badging. I am assuming that this simply verifies that the cylinder assy is for a 686 cm3 engine which of course the stock 700 series HISUN engines are. Am I missing something here or is this just a manufacturer artifact? With or without the badging the application listings all indicate compatibility with the MSU 700 series engines.
      Question 2:  I have reviewed at minimum a dozen videos associated with this rebuild. To date I have not found one that deals with piston/cylinder clearance and/or ring gap verification. The advertised specifications for these various "top end rebuild kits" all indicate: Cylnider bore = 102mm and piston diameter=101.5mm. The math yields a .5mm (as in 1/2 mm) difference. That seems to be a very large piston/cylinder clearance.  I realize I am referencing advertised specs rather than emperically measured values but the numbers have gotten my attention.  I have referenced the FSM and found it to be somewhat confusing in this regard. Hopefully the experts on this forum can enlighten me as to where my observations are faulty here.
      Any and all assistance is greatly appreciated .
      Thank you all in advance,
      Chile
    • Joe Breaux
      Oil change
      By Joe Breaux
      Decided to do an oil change on the Massimo ...drained oil, screen was very clean even tho oil wasn't.  Then went to remove old filter.. holy crap ..I tried every tool I have, could not budge it..Went to store and got one of the end cap type..fit nice and tight, put a 1/2 in drive ratchet on it..nope..not moving.  Put a 18 on breaker bar o. It. The inside of the removal tool broke off!!  Had to weld it back together. Put a pipe on the bar for more leverage.  Finally broke it loose..
      I have never seen a filter in my 55 yrs of working on engines so tight..And i was the one who put it on 2 yrs ago.  JUST HAND TIGHT!
       
    • CSM_Retired
      Kioti K9 Power Dump Kit
      By CSM_Retired
      Has anyone installed the power dump on a Kioti K9? If so, does it eliminate the safety lock? Does it work well?
      Thanks for your input
    • monkthumper
      2020 Hisun Sector 750 no pwr to fuel pump
      By monkthumper
      Fuel pump is good (i hotwired it) swapped relay with known good one no help. I'm leanin towards ECU but cannot find wiring diagram online. Dont know how fuel pump relay gets its signal, all fuses good, any help? 

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...