Quantcast
Jump to content


supercharger kit for t2

CrawlnT2

By CrawlnT2
in Joyner UTV SxS Forum

 Share

Recommended Posts

CrawlnT2 Enthusiast

CrawlnT2

Posted
Posted

Has anyone else run across this? At the bottom of his home page says rjs supercharge kits for joyner buggies but has listed 1100cc fi trooper. Being that I like rock crawling may be a good choice. what do yall thing? www.rjssuperchargers.com

Guest Lenny

Guest Lenny

Posted
Posted

Has anyone else run across this? At the bottom of his home page says rjs supercharge kits for joyner buggies but has listed 1100cc fi trooper. Being that I like rock crawling may be a good choice. what do yall thing? www.rjssuperchargers.com

A super charger is going to give a lot better low RPM torque for rock crawling. You definetely want to use an aftercooler and the engine needs to have the very mismatched prots cleaned up. Lowering the compression is also necessary. And for rock crawling I would go to the renegade diff gearing. Contact Jarrad at No Limit Motorsports about this.

Lenny

CrawlnT2 Enthusiast

CrawlnT2

Posted
  • Author
Posted

A super charger is going to give a lot better low RPM torque for rock crawling. You definetely want to use an aftercooler and the engine needs to have the very mismatched prots cleaned up. Lowering the compression is also necessary. And for rock crawling I would go to the renegade diff gearing. Contact Jarrad at No Limit Motorsports about this.

Lenny

I have already talked to him today. Had to order up two outer tie rod ends and rear axel that I broke this past weekend. We touched on the topic of superchargers today said that you have alot of torque. Do you have renegade gearing?

Guest Lenny

Guest Lenny

Posted
Posted

Well who is going to be first

Yes I do have Renegade gearing and like it. I think Rocmoc is getting ready to put it in his Trooper too.

Lenny

Guest Lenny

Guest Lenny

Posted
Posted

Cool. What is the top speed of yours after the gears? What size tires are u running?

I run 31x10.5-15 Mickey Thompson Baja Claw tires and my top speed is still probably 60-65. It was probably 75 with the stock diff gearing.

Lenny

CrawlnT2 Enthusiast

CrawlnT2

Posted
  • Author
Posted

I run 31x10.5-15 Mickey Thompson Baja Claw tires and my top speed is still probably 60-65. It was probably 75 with the stock diff gearing.

Lenny

That diff gearing makes a big difference cause my top speed is somewhere around 65-70 On 28.5/12/14. I think it may be to low being that I only have 28.5 tires.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • rdc
      Looking for the left side shaft carrier where the rear bearings go for a 2014 1100cc sand viper, I understand an 800 cc carrier will also work.
      By rdc
      I posted this before , but I had the year wrong. The part I need is for a 2014, I don't know what all years will work, but I need the 2 bearing style with the spacer in the middle. It looks like this pic. If anyone has one I'll buy it rite away. my email is [email protected]. Thanks, RC

    • rdc
      Looking for a left rear shaft carrier (just the carrier) for a 2007 Joyner 1100 sand viper
      By rdc
      Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]
    • 180gtr
      Parting out Joyner Sand Viper 1100
      By 180gtr
      Parting out a rolled Sand viper 1100. I will list some of the parts I have, otherwise ask me if there is something specific you are looking for. I am selling everything I have for $800. I am located near Glenwood Springs CO.
      SOLD ITEMS, I do not have these items.
      Wheels
      Tires
      Engine
      Transmission
      Axles
      Shocks
      Control Arms
      Things I have....These all came off of the running engine. I have video of it running if anyone needs to verify that.
      Throttle Body $90
      Starter $150
      Alternator $150
      Fuel rail, injectors, fpr $100
      fuel pump $70
      Map Sensor $50
      Full set of Guages $150
      Exhaust w cat, O2 SOLD
      Ignition Coil - SOLD
      Wiring harness and ecu SOLD
      Radiator, shroud, elec fan, overflow tank $200
      Fuel tank w sender $150 Has dent at base of fuel neck, no leaks
      I have a box full of misc bolts, nuts, etc.
      I will sell the Chassis or Frame alone for $200. The chassis is in pretty good shape, needs some cage repair and 2 areas straightened where control arms mount. If anyone had an automotive frame machine it would take a few hours.
      That would include....
      Brake calipers, lines, pedal, master cyl, E brake assy,
      Steering shaft, wheel
      Ignition switch, key
      Light bar frame, 2 lights
      misc hardware, spindles
      2 hubs, rotors
      Engine mounts
      Throttle pedal, cables
      Shifter, cables
      Clutch master, pedal
      I am sure I am forgetting something.
      I am parting this out of ebay right now, I just picked up another project and could use the room. No I will not take less than $700 for all of it or $200 for the frame. I do not need to sell it, I will make far more parting it out but would like the extra space in the garage.
      If interested I also have an 07 1000rr engine setup I would sell with the buggy for $650.
      Thanks!
















    • Jody Deville
      Joyner 800 Renegade rear axles
      By Jody Deville
      I’m looking to best place to buy replacement axles for the rear in my buggy. Both axles are bad. Where is the best place to find them?
    • Rmillerdesigns
      Massimo Msu 500 Has No Power
      By Rmillerdesigns
      Hello. I have a 2016 Massimo MSU 500. I was putting on a lightbar and i screwed up and didn't disconnect the battery so when i was taking of the positive cable to put on the power from the lightbar it sparked and now the utv has no power. I turn the key over and all i hear is a chirp. No lights or anything. Everything that comes from the battery to the jumper box up by the battery shows voltage but anything coming out does not such as to the winch or anything like that

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...