Quantcast
Jump to content


Chery 1500cc in the Renli Buggy

2scoops

By 2scoops
in Renli UTV SxS Forum

 Share

Recommended Posts

2scoops Proficient

2scoops

Posted
Posted

We need to get info on these and see what a engine and tranny would cost. I will be the guinea pig if it's not to expensive, but I do need to know if they have a low first gear for crawling or I am not interested.

If anyone has any info please share. I will be looking into it as well. 108 NA no sure sounds nice.

Link to comment
Share on other sites
  • 2 weeks later...
  • 3 weeks later...
silverbullet Experienced

silverbullet

Posted
Posted

silverbullet

We have made a deal with a Joyner vendor who dose all drive trains parts.We will supply a trooper rear differentials.We will up grade them with Lenny's up grades.We all know how his up grade work. Price will be 685.00 + shipping.Will have supercharger very soon.We spent a lot of time making this innovator supercharger.We have tested it for months.Found small things and fixed them an are satisfied with this will be a bolt on system.Working on fabricating jigs to build the units.But differential are hear now.

Link to comment
Share on other sites
  • 2 weeks later...
  • 4 weeks later...
  • 9 months later...
silverbullet Experienced

silverbullet

Posted
Posted
On 7/10/2016 at 7:25 AM, Yoshio said:

Will the supercharger fit sandviper model also? What's the suggested price for it? More details!

silverbullert

It will fit all chery based buggys.Water Meth system is done we are working on the supercharger.We have one tech working on it till it is finished.This is all he is working on till done vary soon it will be ready.I have so many customs who want it.I can't wait till its on the Dyno to see the Torque its put out.He is finishing the small details.Mount Bottle,pump for Meth.Egt gauge and air fuel ratio gauge.10 days at most still have to get in touch with Dyno shop.On Monday

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Reynolds Rocket
      2017 Intimidator XD4 800 Check Engine
      By Reynolds Rocket
      I have a 2017 Intimidator XD4 800cc 4x4.  It will run great and then it's like it goes into safe mode and only runs on 1 cylinder.  It's not fouling out the plug when it happens.  Some times when I stop and restart it, it works fine.  First I thought it was a spark issue, then a fuel issue, but I feel like it's a short in the wiring some place. 
    • lmarkie
      Bulldog BD700 Engine Swap
      By lmarkie
      I swapped out the Subaru motor for a Predator 670cc. If I remove the heat shield around the muffler, The stock muffler sits in there just fine with 1" to spare.
      Only problem is the exhaust exit is toward the back seat instead of out the back.
      Do you all think that the stock exhaust would be okay (just as effective) if cut a hole and welded a pipe on the reversed (opposite) end? Of course, plug the old exit end. Other option I thought of was to roll a tube 180° with a 7" center line radius and finish extention of 12" or so.
      Any thoughts?
    • didgeridoo
      Hisun Sector e1 Battery replacement: any tips?
      By didgeridoo
      Hello, All!  I've decided to replace the traction batteries in my 2018 Sector E1 with a 48V Lithium set. They may be expensive, but I figure the Discovery Dry Cell are, too. I am not looking for the max driving range, as I have never received near the brochured range to begin with, but a good mix of charge/ get work done/ charge is what I am expecting.
      I have settled on the 48V EAGL kit from bigbattery dot com. Each battery pack provides 30Ah. The kit ships with a charger, as well. The packs would be physically connected in parallel (using a busbar) to one another, maintaining the 48V voltage, but together would be able to provide the amp draw the buggy pulls when going up hill or towing a rake (rated 320 max continuous Amps). This is in comparison to the serial connection the eight 6V lead batteries. Each of the EAGL batteries looks to have its own BMS; am I correct in thinking I will have to use their included charger rather than (simply) changing the onboard charger to lithium mode? The chemistry of the pack is LiFe PO4, for what it's worth.  I haven't torn anything apart yet (to diagram), so  I am not sure how the dash will interpret the AMP draw, but the kit I am looking at includes a dash mounted charge indicator.
      If anyone has completed a similar conversion, do you have any tips? Specifically, how did you remove the original batteries, and how did you secure the new ones? I am guessing that almost any change from the stock batteries would involve at least some modifications. Any tips would be appreciated, especially things I may have failed to consider. Thanks!
    • JOSEPH LAMAR
      Please help me solve this
      By JOSEPH LAMAR
      I have a 2020 axis 500 and I have replaced the TPS twice and the whole throttle body assembly once and still have code 122. I can barely drive the thing. It bucks and surges like crazy
    • redneckred
      2012 Bennche 700X Engine code
      By redneckred
      Can anyone tell me how to get the engine codes to display on a 2012 Bennche Bighorn 700X?  I played with the gauges once and lucked up on this but can't remember what I did.  Will the codes automatically display if there is a code or do you have to cycle through the display?

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...