Quantcast
Jump to content

Trooper Rear Differentail


silverbullet
 Share

Recommended Posts

silverbullet

We have just found a way to use our 6 cylinder controller.4 for the engine and 2 for the extra injectors  1 for fuel and 1 for the water meth injection.1 will injects the extra fuel and the other with water meth.Snow performance gave us some information to solve this meth injector.We have used a maff 5v sensor for the 2 extra injectors.The 2 injector will  be under the supercharger will cool the charge buy 150 to 200 degrees and raise the octane buy 15 points witch well make 89 octane in to race fuel 115 octane.A sensor for low meth in bottle.

Link to comment
Share on other sites

  • 4 weeks later...

Silverbullet

We sold them out.will get them in 2 weeks.The only way i can sell it at this low price is i let customer pay for it than order it.I takes 15 days to get it shipped to us than we ship it to you.I will give you a UTV board discount.The total price will be 735.00 shipped to your door.

Thanks Rich

Link to comment
Share on other sites

  • 4 weeks later...
  • 4 weeks later...
  • 2 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

  • Similar Topics

    • By RickinMT
      I bought a new Axis 700 at Lowe's last Sunday, 7/24, and I didn't look through all my paperwork until the next day and there is no warranty info in the packet. I checked the Hisun site to see if you can register yourself and provide proof of purchase, etc., but they only have a form for Pre-Delivery & Customer Orientation Checklist which is to be filled out by the dealer and submitted to Hisun within ten days. I just called Lowe's and they're saying they automatically send it all in. How can I verify my warranty is registered with Hisun? I tried their phone number but of course right now it's after hours. I'll call again tomorrow but 10 days is pretty near.... I don't have any warranty claim yet but I just want to be sure it's registered.
      Does anyone know a better way to check?
      Thanks.
    • By Robert G1
      Hi all. I'm new to the site. A few years ago I bought a used Massimo. Recently I've had a issue driving above 25mph. The engine won't go any faster. In fact it seems to sputter and hesitate. The whole engine shakes. I've changed air filter.oil,oil filter, throttle cable oil/air cooler,and carburetor and still no luck. I was wondering, could it be the fuel pump. Should I invest in an electric fuel pump? I'm just not sure. It starts fine and revs while in neutral. Any advice would be great. Thank you 
      VID_20220722_110957473.mp4
    • By RickinMT
      I'm still in the break in period and this thing is vacuuming up all the dust in the world. I had sealed up my old one pretty good but this one, wow. Looking to hear some input on where to duct-tape and seal, and what you guys use for same. I blew it out today with my compressor and I'm sure I should check the air filter already. Only 9 hours on it but I bet it's bad. I'll be adding soundproofing materials as a winter project, like I did on the old one, and that's when I'll have all the plastic under-seat panels out, so I'll be able to seal up everywhere I can.
      The other question is, do I run the risk of trapping too much heat if I do too good a job? How critical is the air intake behind the driver's seat for the belt cooling duct? Should I extend the duct out somewhere? I have the dust/heat shield on it, the one that stretches behind the seats and comes up behind to deflect dust out back. It doesn't seal the under-seat areas very well, though.
       
      Anyway. TIA.
       
       


    • By lonerider98
      I have a 2013 Coleman ut500. When riding I get a lot of heat coming from behind the seats. Has anyone put some kind of heat shield to stop this heat? It get quite warm on long rides! T.I.A.
    • eManualOnline
    • By Wyatt Carneal
      Hey guys.
      I have a 2009 hisun 700 I bought bout 2 weeks ago and it was running fine but was hard to start but once warm it fire rite up  i took the  air filter off and it was nasty so I gave it a good cleaning and it hasn't started since. Its cranking over really slow I replaced the starter. I also replaced the batery. It acts like its not releasing decompression  I found a service manual on line and downloaded it and it said the intake valves setting .010-.015 mm  and exhaust is .015-.020 and they all was set on .008 intake and exhaust. And the timing is set I set the intake to .012 and exhaust to .016 and it still cracks over really slow I'm lost and don't know wat else it could be. Anyone have any ideas.  And help would be great thanks .
  • Gallery Images

×
×
  • Create New...