Quantcast
Jump to content


Hisun 250 - Brake Locked up

CStrike250

By CStrike250
in Hisun UTV SxS Forum

 Share

Recommended Posts

strike250 Community Regular

strike250

Posted
Posted

More than likely just a belt, but inspect it first. You might have gotten lucky. As for the breaks, look at a Yamaha banshee or raptor, same exact brake caliper. Yamahas manuals are much better on rebuilding brake caliper than HiSUN. The brake pads from EBC are listed in the parts interchange list in the download section of my website. Do not go off EBCs website, they have the incorrect parts numbers. The correct ones are listed on my site. Hope this helps

strike250 Community Regular

strike250

Posted
Posted

As for the pistons in the brake caliper, they are held in place by O'rings. If you are having problems with the brake caliper being locked up, it sounds like maybe you have contaminated fluid, causing it to crystallize and seize the caliper in place. You should be able to use compressed air on the banjo fitting side of the caliper to force the piston out. If not, then you can soak it overnight in wd40 type of fluid to try to penetrate the back side of the piston and help release it. If not, I would just purchase a new caliper. These calipers are the same as Yamaha Banshee or Yamaha Raptor 600.  You can find a bunch on ebay. The piston does not screw in, it should simply press in and out. Remember to use quality brake fluid, DOT 3 or 4 is fine as it again sounds like the fluid has water or something else that caused contamination.

The brake pads used are: Front brake pads: EBC FA54
                                                         Rear brake pads: EBC FA83

CStrike250 Apprentice

CStrike250

Posted
  • Author
Posted

Thank you very much for your help, turns out the o ring was pinched in between the piston and the wall causing it to bind up. Was a pain getting it all apart. I am thinking I could get away with a rebuild kit but I cant seem to find any  banchee or raptor 600. I see 700 raptor and 660 banshee but not 600. I went into a yamaha parts dealer and tried to get the schematics of the brakes to see if it "looked" the same but had no luck. I am leaning toward just ordering a whole new caliper from one of the web link you have on your website.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Chile
      Massimo MSU 700 Piston Clearance
      By Chile
      2018 Massimo MSU 700 EFI. I realize that this engine is essential the same as in all of the HISUN based Yamaha clones out there. I am in the process of performing a top end diagnosis/rebuild. I have an AMAZON top end rebuild kit on order in anticipation of this activity. 
      Question 1:  When exploring the myriad of top end rebuild kits on the market for these units there are some cylinder assemblies that have "686 cm3" badging next to the cam cain tensioner boss. Others compatible with the unit do not have this badging. The existing cylinder assy does not have the 686 badging. I am assuming that this simply verifies that the cylinder assy is for a 686 cm3 engine which of course the stock 700 series HISUN engines are. Am I missing something here or is this just a manufacturer artifact? With or without the badging the application listings all indicate compatibility with the MSU 700 series engines.
      Question 2:  I have reviewed at minimum a dozen videos associated with this rebuild. To date I have not found one that deals with piston/cylinder clearance and/or ring gap verification. The advertised specifications for these various "top end rebuild kits" all indicate: Cylnider bore = 102mm and piston diameter=101.5mm. The math yields a .5mm (as in 1/2 mm) difference. That seems to be a very large piston/cylinder clearance.  I realize I am referencing advertised specs rather than emperically measured values but the numbers have gotten my attention.  I have referenced the FSM and found it to be somewhat confusing in this regard. Hopefully the experts on this forum can enlighten me as to where my observations are faulty here.
      Any and all assistance is greatly appreciated .
      Thank you all in advance,
      Chile
    • Wolfpaak
      Identify this part help needed
      By Wolfpaak
      I think this part is causing a high idle problem(4000 rpm at start up) in my 04 R4 Joyner. I took it out and cleaned it and the problem went away. I just went out to start my SXS and it's idle jumped up to 4 grand again. Can someone tell me what this part is called so I can search for a new one. Or can you point me towards a source. 
      Thanks in advance. 
      Kenny


    • SkyPilot56
      working on a coleman 550 out fitter
      By SkyPilot56
      working on a coleman 550 out fitter , had a shit load of codes, coil, injector , and the map sensor for fuel injector replaced all 3 and figured it would start , but no joy have spark (new plug also and inline fuel filter) cleared the codes and still have the engine light , turns over fine but damn thing still will not start, friends daughters were driving it and turned it off to park , and went back to start it and same thing turns over but will not start , with this machine anyone have any ideas as to what the hell , I should be looking for , no plug's unplug checked wires none seem to be pulled apart or broken !
    • Jon Spruill
      2018 Hisun Sector 1000 Crew stalling but starts right back up. Please help!
      By Jon Spruill
      Hey Guys, I have been chasing a stalling condition for about two weeks now. The bike will crank up and idle fine, then after about 20 seconds it will fall on its face and stall. It happens at both idle and while running at various rpms. You can turn the key off, turn it back on and it will fire right back up without trouble. I have verified spark on both cylinders with a spark tester. I have also added an inline fuel filter, and pulled the injectors to verify proper pulse on each. Things I have replaced - (relearn procedure performed after each component replaced): spark plugs, ECU, relay/fuse box, fuel pump, & throttle position sensor - all with no improvement of the condition. The only warning light I get when the condition occurs is the oil lamp. The bike only has 14 miles. I am at a loss and appreciate any help and suggestions! Thanks
    • A P
      2022 Hisun Sector 550 eps. Power steering not working
      By A P
      Hi
      I have a 2022 hisun sector eps 550. 30amp fuse is blown for eps. Checked the motor and it’s fine. Opened up the controller and found a bad diode. Dealer wanted 500$ for the controller. Just posting this in case it helps someone. I couldn’t read numbers from the old one so just took a guess and replaced it with a 100v 3amp diode. 

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...