Quantcast
Jump to content


2018 Cub Cadet 750 Clutch Issues

Cub owner

By Cub owner
in Cub Cadet UTV SxS Forum

 Share

Recommended Posts

Cub owner Newbie

Cub owner

Posted
Posted

Ok trying again... I have 2018 cub cadet 750. Having clutch issues. Has anyone bought a upgrade for them and where did you get them and about how much. Thanks for any help given. From what i have looked over on here. Lots of nice helpful people 

  • Like 1
Cub owner Newbie

Cub owner

Posted
  • Author
Posted

The clutches themselves. There is like 3 of them I guess. Wet clutch primary secondary from what I hear. My problem is taking off and can't get my speed anymore once it does grab good.

  • 2 months later...
groged67 Rookie

groged67

Posted
Posted

I just put in a EPI clutch upgrade. My starting system is messed up so I can’t review it for you yet.

Putting it in was not too bad. Buy the tool for the secondary clutch though. No way to do it safe otherwise.

  • 5 months later...
Thomas osterhout Apprentice

Thomas osterhout

Posted
Posted
On 11/7/2019 at 11:27 PM, Cub owner said:

Ok trying again... I have 2018 cub cadet 750. Having clutch issues. Has anyone bought a upgrade for them and where did you get them and about how much. Thanks for any help given. From what i have looked over on here. Lots of nice helpful people 

How did u make out with your clutch

  • 11 months later...
Dean61 Newbie

Dean61

Posted
Posted

Misfiring after shifting from low to high.

After shifting gears the cub 750 challenger starts to misfire and barely will run. Any suggestions. It idles great and runs good until it shifts. 2018 year.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Frank Mac67
      AXIS 500 WILL NOT START. HELP!
      By Frank Mac67
      My Axis 500 has been operating properly for almost a year with Zero problems. While I was away my granddaughter & friends were riding & playing in the snow. They went to the gas station to fill the tank & the vehicle would not start afterwards. I BEEN GIVING MULTIPLE STORIES: The ATV will not start. When I turn the key I can hear the fuel pump come on but nothing happens other than that. 
      - NO CLICK - NO OTHER NOISE
      *I CHECKED THE BATTERY 12.43volts
      *I replaced the solenoid inside the battery compartment. 
      Seems the next electrical component in line has battery connections IN & motor connections OUT with 2 other small wires connectedaswell(I do not know the name of this component).
      Can anyone help?
      I can not find an ordered list of electronic components starting at the battery.
      Can anyone help with this?
      Thanks in advance for any help.
       
    • monkthumper
      2020 Hisun Sector 750 no pwr to fuel pump
      By monkthumper
      Fuel pump is good (i hotwired it) swapped relay with known good one no help. I'm leanin towards ECU but cannot find wiring diagram online. Dont know how fuel pump relay gets its signal, all fuses good, any help? 
    • CaptainMorgan
      Bobcat 2200 Diesel Primary Clutch Rebuild
      By CaptainMorgan
      I have a Bobcat 2200 Diesel (built by Club Car) with a 2-weight Team Primary Clutch I want to rebuild, possibly replace. The clutch has an annoying rattling sound at idle and appears the rollers and weights are worn and loose. When I opened it up, everything looks clean and in great shape. It's just that all the moving rollers and weights seem to have way too much play in them, possibly causing the noise. I've searched for clearance and torque specifications with no luck at all. The UTV has less than 500 hours on it.  Any ideas?
    • Flanman55
      Wiring issues
      By Flanman55
      I have purchased a used Supermach700 (2008), It runs great after a new choke cable but. The temp sensor on the thermostat house is unhooked and can not find where it plugs back in. The fan has been un hooked from the sensor in the rad and cant figure out how it goes back together properly.  The fan was wired to a by pass switch and i just always leave it on but would like to work it properly. I assume the sensor went bad and not changed.
       
      any help would be great.
       
      thanks
    • Wolfpaak
      Identify this part help needed
      By Wolfpaak
      I think this part is causing a high idle problem(4000 rpm at start up) in my 04 R4 Joyner. I took it out and cleaned it and the problem went away. I just went out to start my SXS and it's idle jumped up to 4 grand again. Can someone tell me what this part is called so I can search for a new one. Or can you point me towards a source. 
      Thanks in advance. 
      Kenny


UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...