Quantcast
Jump to content


help with kaf950b diesel

brian kessner
 Share

Recommended Posts

brian kessner Rookie

brian kessner

Posted
Posted

i have a 2007 3010 mule 950 diesel 4x4 it will drive but feels like something is binding then it feels like it brakes loose then will do it over again. at fist i thought it was a belt going bad  replaced it and it still is the same. could it be the front differential, transmission or rear differential and how do i find out which one it is

kenfain Experienced

kenfain

Posted
Posted
20 hours ago, Travis said:

I would start with something easy first, and check that your brakes aren't dragging. Jack it up, front and back and spin the tires.

I have a similar machine, and my wheels won't really spin when it's in the air. Not by hand anyway. Because you're also turning the differential.

But I agree that it needs to be jacked up, and on stands. That'll help pinpoint the problem wheel, or wheels. 

Just be careful to make sure the wheels aren't spinning when you put it in, or shift gear.

  • Like 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • CaptainMorgan
      Bobcat 2200 Diesel Primary Clutch Rebuild
      By CaptainMorgan
      I have a Bobcat 2200 Diesel (built by Club Car) with a 2-weight Team Primary Clutch I want to rebuild, possibly replace. The clutch has an annoying rattling sound at idle and appears the rollers and weights are worn and loose. When I opened it up, everything looks clean and in great shape. It's just that all the moving rollers and weights seem to have way too much play in them, possibly causing the noise. I've searched for clearance and torque specifications with no luck at all. The UTV has less than 500 hours on it.  Any ideas?
    • rsar
      Washing Mule Underbody
      By rsar
      Hey guys. I was wondering if anyone pressure washes their Mule underbody. Three years in, I have yet to do this. I'm worried that the pressure washer could damage or dislodge something but it's gotten to the point that it could use a bath. Any thoughts?
    • D MAYNARD
      Axis 500 4x4 turns over but no spark
      By D MAYNARD
      I have an Axis 500 4x4 UTV that I was given.  It looks like an almost new machine with 39 hrs on it however it was apparently under water from the hurricane . I have no spark at the plug. I have replaced the plug, the plug wire, & the stator so far. Can anyone advise me of what i need to check and or replace to get this thing running? Any advise would be greatly appreciated. 
                                    Thank You,
                                  D Maynard 
       
    • TjB
      2510 Kawasaki mule Diesel
      By TjB
      My dad has recently acquired a 2510 Kawasaki mule Diesel powered. It worked fine  few weeks and then quit driving. Put a new belt on just to see. Still not driving. It already had a new clutch. Belt turns when in drive or reverse and back wheels are off ground to test. But wheels not turning. Thoughts? 
    • Will D
      Mule 4010 trans overheating
      By Will D
      Hello, I have a mule 4010 trans that appeared to overheat based on the temperature light on the dash and it went into limp mode.  No steam though.  After letting it cool and the next day, I drove it around quite a bit and it did not have any problems.  Any ideas on this.  Do thermostats work intermittently?  I would like to fix the problem, looking for advice.  Many thanks 

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...