Quantcast
Jump to content


2018 Textron Stampede 4 Engine quit and will not start.

ChopperPilot01
 Share

Recommended Posts

ChopperPilot01 Rookie

ChopperPilot01

Posted
Posted

Bought a used Textron Stampede 4 with 30 hours.  Engine quit and will not start.  CodesP0031, P0261, and P0264 showing. Closest dealer is 100 miles away.  Sure would appreciate any help with what the fix may be.  Thank you, Paul

cliffyk Rising Star

cliffyk

Posted
Posted

What a wonderful service manual--I need to send it to Hisun and Coleman so they can see what one is supposed to look like!

In reviewing the wiring diagrams I see that he injectors, Lambda (O₂) sensor and ignition coils share a common power feed from terminal C6 on the main harness (this is good news as it links directly to the DTCs):

StampedeWiring-00.thumb.jpg.3da09c0953490e81150aafbdaf675255.jpg

On the wiring harness it looks like this--with SP1 (SP=splice???) being a common connection point:
StampedeWiring-01.thumb.jpg.58f89bc263e8e307d9f8afa97c800e5e.jpg

They also provide this splendid illustration of where all this stuff is located (though the O₂ sensor does not seem to be shown)

StampedeWiring-02.thumb.jpg.dade79ded10ed497ad1fca965f51167a.jpg

Before hauling it 100 miles check that main harness connector, and the  connectors at he injectors and coils  to make certain they're not corroded or otherwise fouled. Check all ground connections as well--check the O₂ senor connector as well as it is quite possibly located is a place that can collect all sorts of crap.

Also, the usual suspects, battery connections, voltage

 While cranking [at the terminals, not he battery posts], , etc. It may be coincidence that all three reported "low voltage" at the same time but I'd look for a common wiring problem.

 

-cliff-

  • Like 1
ChopperPilot01 Rookie

ChopperPilot01

Posted
  • Author
Posted

Cliff, thank you so very much for taking the time to show me some possibilities that could be the cause my issue.  I will do my best to sort it out with your most welcome help. I have checked the main grounds and connections to frame grounding and they are all tight and seem to be in good condition.  I will certainly take your advice and do my best to check things out.  Thanks again Cliff, I really appreciate your help! Paul

cliffyk Rising Star

cliffyk

Posted
Posted
2 hours ago, ChopperPilot01 said:

Cliff, thank you so very much for taking the time to show me some possibilities that could be the cause my issue.  I will do my best to sort it out with your most welcome help. I have checked the main grounds and connections to frame grounding and they are all tight and seem to be in good condition.  I will certainly take your advice and do my best to check things out.  Thanks again Cliff, I really appreciate your help! Paul

You are quite welcome--let out a yell if you have any questions, or just want to bounce around some ideas. I don't believe the O₂ sensor issue would prevent the engine from starting.  Try unplugging it, if it's heater is drawing too much power and dragging that circuit down disconnecting it "might" allow the engine to start--worth a try, if it starts you know which part to buy...

-cliff-

ChopperPilot01 Rookie

ChopperPilot01

Posted
  • Author
Posted

Thank you for another most welcome suggestion Cliff.  I hope to check all of your suggestions this weekend.  I have looked around the engine compartment and it is pretty tight with all wiring covered, so I hope I can find the connections........ I will post what I find or cannot find.  Thanks again for taking time to help me out... 

Paul

  • 3 weeks later...
ChopperPilot01 Rookie

ChopperPilot01

Posted
  • Author
Posted

Hello Cliff, I wanted to say thanks again for taking time to help me out.  I had to take it to a local ATV shop and hope for the best.  They figured it out!  It was a bad cam sensor and it caused several other codes to be displayed as well.  The common error was the cam sensor.  I ordered one through Country Cat (a great source for many makes and they are helpful as well) and had the part it 2 days and all is good for now....  Thanks again Cliff .   Paul

  • 4 years later...
Samuel Newbie

Samuel

Posted
Posted

IF yall still get notified I wanted to post. I have a 2018 Textron Stampede. It's never gave any trouble. recently it decided not to start. So I went ahead and did the basic maintenance anyway. Changed the oil, oil filter, Air Filter. New spark plugs, Battery is good. tested fuses all seem to be good. Engine is fine, starter is fine. I believe I've narrowed my issue down to a fuel pump. Just curious if anyone has experienced issues with those. Thanks in advance

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Jon W
      Havoc VS Stampede Motors
      By Jon W
      looking around and cannot find and Stampede motors, the Havoc looks to directly bolt in, with exception of the larger displacment. has anyone looked into this further? seems to be a better option considering stampede engines are on backorder. 
    • BWF
      Landmaster LM200 Will Not Start
      By BWF
      I have a 2011 or so Landmaster LM200.  I cannot get it to start.  I turn the key and nothing happens.  The brake switch seems to be working, the ignition switch works.  The Coil is new the Voltage Regulator is new and the starter relay is new.
       
      I can connect the terminals on the starter relay and it starts right up and runs fine.  I just can't get it to start by turning the key.
       
      I am having a bit of trouble bleeding the brakes, not much fluid comes out at the calipers when I am pumping the brakes, though that an air bubble near the brake switch might make it not sense that the brake pedal is depressed.
       
      I am at a loss, please help!
       
      Brad
    • Mitch13
      Coleman 400 wiring help
      By Mitch13
      2022 Coleman 400 with 13 hours on the engine and the mice got to it. Every wire coming out of the steering column in one cluster has been eaten through. I tried reconnecting matching wire colors to each other and I get the left turn signal and hazards to work, nothing else. If I play around a bit I can get the horn to honk or headlights to come on but only when I connect them to the brown wire. Obviously I don't know what I am doing here. Does anyone have a picture of how these wires are connected when they are under the hood on the drivers side coming from the steering column?
      Gray - seems to carry power
      Brown - left turn signal
      Green with purple stripe - hazards?
      Pink with red stripe - horn?
      Green - head lights?
      Yellow - head lights?
      Yellow with red stripe?
      Blue?
      Dark green?
      There is also a bundle hanging under the hood not connected to anything green with yellow strip, brown and blue?
      Other than that issue, I am about ready to sell this for parts if you interested let me know.
      Thanks
    • RBonds007
      2019 Cub Cadet Challenger 400, trailer to transport the Challenger, and new, never used winch for sale
      By RBonds007
      I bought this SxS brand new.  A couple of years after I bought it, I became disabled.  Thus it has only 47 miles and around 16 hours of use.  I have no need to keep the SxS.  I am in Foley, Alabama.  It is very hard for me to get in out of the Challenger.  I would like to sell the set, 2019 Challenger 400, trailer and uninstalled winch (this was bought brand new as well, someone was supposed to help this newbie install and we never got around to doing this). I want  $6500 for the whole set OBO (Serious offers only).











    • Jeff freeman
      Utv wont start and broken fuel injection wire
      By Jeff freeman
      I have a Coleman 550.  Was having problems to start with where it would start and then shut off after a couple tries. It would take off and be good. It then got to a point where it would not start at all. I replaced the fuel injection twice the second time I replaced it I noticed a mouse or something had chewed one of the wires that connect the electrical to the fuel injector. . So two-part question first does anybody have a part number for that wire harness?  Second, any other ideas after I fix the wire harness permanently on what could keep it from starting I have gas flow up to the fuel injector.


UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...