Quantcast
Jump to content


HiSun Sector E1 Error code E038 and E013 what does it mean?

Jurg

By Jurg
in Hisun UTV SxS Forum

 Share

Recommended Posts

Jurg Newbie

Jurg

Posted
Posted

Trying to charge over night I found the unit with a flashing amber LED both in the dash and on the charger next to the lh front wheel. 

The first error code I got was E038 on the charger with my next attempt I got E013.  The battery is not being charged.

??

BuggyBoy Explorer

BuggyBoy

Posted
Posted

E013 is an issue with loose connection or an external device interfering with charging. 
got same with mine but can’t see any loose wires or connections and no other device has been installed. 

have emailed manufacturer of charger with details and data log from charger. 
 

did you resolve it?

BuggyBoy Explorer

BuggyBoy

Posted
Posted

'E013 - Charger Output Current NotAccepted - Battery voltage is detected but the charger is unable to output current. This is normally caused by an electrical device connected between the charger and the battery which passes through voltage but not current.  Poor connections can also cause this.  Ensure the charger is properly connected to approved equipment. This error will automatically clear once the charger is reset by cycling DC or AC'.

EVSupport Enthusiast

EVSupport

Posted
Posted

Suggest you check all the cabling back to the main connections to the battery pack. They are under the central hoop under the seat look for the connector with the plastic block and two leads, thats one of the charge cables. The second lead  is the temp sensor lead in that plastic  block. But check all the battery connections. Also check under the cover of the Delta Q charger on the right (passenger side ) side are all the wire connections take off the cover (two torx screws) and then carefully check the tightness of the torx screws holding the two larger charge leads . Its easier to take the front wheel off than simply inserting your head between the wheel and the front arch.

BuggyBoy Explorer

BuggyBoy

Posted
Posted

Took off the small cover on charger and cables look ok and were all tight. 
however, decided to add another pos cable to bypass current pos cable from charger to battery as a test before I dismantled for warranty testing/return and it worked, now charging and no fault. 
The Pos/Neg charger cables seem too small a gauge for the current (3-4mm?) going through them.  I’m going to upgrade the charging harness to 6mm to stop overheating and cable breakdown. 
Thanks for your advice. Are you Hisun EV support or independent? 

Jurg Newbie

Jurg

Posted
  • Author
Posted

There was a loose connection on the front battery, second row from the left. On the same row one battery back there is a connection with a (former) 30 amp fuse holder. That connection on the battery was not completely tightened. But the fuse holder cap was unusually bulged and the cap fused to the body. Further investigation revealed that the fuse inside was completely melted and disintegrated. I am going to fix that and hope that this will resolve the problem. It definitely looks like all your comments are correct. Thanks to everybody!

 

EVSupport Enthusiast

EVSupport

Posted
Posted

The cable for the charger DC side  is normally quite adequate. You will struggle to get larger in to the housing easily. Dont solder only crimp. If you cant crimp get someone who can. And you will need to ensure the negative side has the temp sensor connection.

Im not  connected to Hisun, but I do Hisun E1 Li Ion conversions in the UK. So see them on an almost constant basis.

BuggyBoy Explorer

BuggyBoy

Posted
Posted

I’d love to convert mine to Lithium batteries. 
I think I’ve read one of your posts a few years ago where you said it’s actually not that difficult, just time consuming. You mentioned changing an algorithm in the battery controller or charger from memory? Apart from physically fitting the batteries, is that about it?

EVSupport Enthusiast

EVSupport

Posted
Posted

All new steel and ally battery enclosures, all new battery / connection cabling,  New loom for the Battery management / Vehicle interface/ charger, new small display, New algorithm on the Charger, re programe the Sevcon , New rear arch cover sections to reduce crud. New mains inlet and relay box in the front compartment. So not a lot , just takes me about 4 days start to finish  with all the parts ready made and in stock.  Some photos on my EV Support Facebook page   https://www.facebook.com/EVSupportUK

 

 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • didgeridoo
      Hisun Sector e1 Battery replacement: any tips?
      By didgeridoo
      Hello, All!  I've decided to replace the traction batteries in my 2018 Sector E1 with a 48V Lithium set. They may be expensive, but I figure the Discovery Dry Cell are, too. I am not looking for the max driving range, as I have never received near the brochured range to begin with, but a good mix of charge/ get work done/ charge is what I am expecting.
      I have settled on the 48V EAGL kit from bigbattery dot com. Each battery pack provides 30Ah. The kit ships with a charger, as well. The packs would be physically connected in parallel (using a busbar) to one another, maintaining the 48V voltage, but together would be able to provide the amp draw the buggy pulls when going up hill or towing a rake (rated 320 max continuous Amps). This is in comparison to the serial connection the eight 6V lead batteries. Each of the EAGL batteries looks to have its own BMS; am I correct in thinking I will have to use their included charger rather than (simply) changing the onboard charger to lithium mode? The chemistry of the pack is LiFe PO4, for what it's worth.  I haven't torn anything apart yet (to diagram), so  I am not sure how the dash will interpret the AMP draw, but the kit I am looking at includes a dash mounted charge indicator.
      If anyone has completed a similar conversion, do you have any tips? Specifically, how did you remove the original batteries, and how did you secure the new ones? I am guessing that almost any change from the stock batteries would involve at least some modifications. Any tips would be appreciated, especially things I may have failed to consider. Thanks!
    • paul allen
      2016 wildcat tail front axle rubber boot
      By paul allen
      right front axle cv joint boot keeps getting torn up from the inside out....the stock one was damaged from a stick...i have replaced  the axle 4 times with aftermarket axles that fit fine..after 4-5 miles of riding even on grass.the outer boot get torn up from the inside out...all 4 brand new alxes...bearings are fine nothing bent everything fits just fine....nothing seems to be binding.....any thoughts?????
       
       
      thanks...pa
       
    • dragon
      2016 Kubota 1100 RTV Tilt Steering wheel locked Upper Position
      By dragon
      I need help I have a 2016 Kubota 1100 RTV my tilt steering wheel locked in the upper position after using the side release. The handle works but does not release the steering wheel to a lower position. If anyone knows and easy fix, please let me know any help is appreciated. Be Safe, Thanks!
    • dragon
      2016 Kubota 1100 RTV Title Steering wheel locked
      By dragon
      Hi everyone, I am new to the site and I have one question. My tilt steering wheel is locked in the upper position, and I was hoping for someone could help me with the problem. I did spray some WD 40 in the area of the mechanism but still wheel is locked in the upper most position. I am willing to try anything to get the wheel free and move to a lower position. Any ideas will be appreciated. Thanks!! and Be Safe! 
    • Terry B
      Hisun Axis 500 purchased from Lowes battery drain
      By Terry B
      We purchased this UTV less than 60 days ago and now I am having issues with drained battery. Used UTV for about an hour then stopped and when I went to start back up my battery was to low to start it. Jumped it and it started right up and ran fine back home. Tested charging and it’s not charging while running. Can it be anything other than the stater??? Can I look for something that I can fix Quik or does it have to go to the authorized service center to stay under warranty? It will take some time to get it in and out of service 

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...