Quantcast
Jump to content


2021 Massimo T-Boss 550 fuel supply issue

JDSmith

By JDSmith
in Massimo UTV SxS Forum

 Share

Recommended Posts

JDSmith Rookie

JDSmith

Posted
Posted

I have a 2021 Massimo T-Boss 550. It was submerged in water for a period (hurricane). All filters/fluids were drained and replaced/refilled immediately after as well as air box cleaned. Drained fuel tank, popped the supply line off and key cycled to clear the line of contamination. Reconnected line and filled with fresh fuel. The machine fired and sputtered for maybe 30 seconds and died. Upon attempting restart I noted the fuel pump wasn’t priming.  I checked voltage at the pump and it is 12v. I’ve replaced the coil pack, wire, ecu, ignition (which was failing just prior to the water event) and the fuel pump. The new pump still does not engage. Rechecked with new pump and there is 12v at the plug on top of the tank as well as down at the pump. I’ve popped apart all the plugs I can see, sprayed them with terminal cleaner and applied dielectric grease. Still nothing. I’ve talked to a buddy and he has said it has to be a connection or ground issue.  Anyone able to point me to specific plugs wires etc to check? I’m paying for the answer. 😂 

  • Alex changed the title to 2021 Massimo T-Boss 550 fuel supply issue
JDSmith Rookie

JDSmith

Posted
  • Author
Posted

I will have to look for that relay. From what I can see I believe my fuel pump relay is a little different.  I don’t have a relay checked for this type, but I wasn’t thinking it was the issue as I can feel the click in the relay when key is cycled. No more than they cost and it’s not like I haven’t thrown $400-500 at it already I should just try it I suppose.

7A901247-E954-451F-8294-50BD6677DDA1.jpeg

  • 2 weeks later...
JDSmith Rookie

JDSmith

Posted
  • Author
Posted

Tank was drained and refilled. Purged line and reconnected. Started and ran for about 15 sec before dying. Noticed at that time the fuel pump wasn’t priming anymore. 
 

I’ve also replaced the fuel pump. So unless the original and then the new replacement was bad, it’s not the pump.

  • 5 weeks later...
  • 1 month later...
Greg Kilgore Community Regular

Greg Kilgore

Posted
Posted

I know its an older post. But I agree that it seems like it is a ground issue. If the original poster would post his resolution that would help.

But some info on relays and power. And if I wrong it won't be the first time.

The relay should supply the positive 12V DC power. To whatever. The ground or negative side should go to a frame ground or back to the battery.

Frame grounds are a lot of problems on many many electrical issues on a lot of vehicles. Whether it's a side by side or a 2001 GMC Sierra dash cluster (don't ask) or a 1997 Dodge Dakota dash cluster (ground point under the kick panel on driver and passenger side).

Cleaning the ground points or running a ground wire back to the battery should resolve the issue. If the fuel pump and relay is good.  

But usually there are many circuits feeding off one ground point. So it would be best to follow the ground coming off the fuel pump to make sure the ground point is making good contact to frame. 

The ground wire can be tested with a multi-meter.

1. Set multi-meter to OHMS.

2. Hold one lead of multi-meter to the other lead of multi-meter. The reading should be 0.0 to maybe 0.2. That will be the reference of the meter and also tells you there is little to no resistance between the leads.

3. Now take the negative side of the fuel pump wire to one lead of the multi-meter. and touch the other lead to a UNPAINTED part of the frame. The reading should be the same or maybe 0.1 more than when you touch the leads of the meter together. 

If no reading or a very high reading that would indicate a bad connection to ground somewhere and the ground point would need to be cleaned.

 

Hope this info helps you or someone. I'm not responsible if anything unwanted happens while you're testing.

 

JDSmith Rookie

JDSmith

Posted
  • Author
Posted
3 hours ago, Greg Kilgore said:

I know its an older post. But I agree that it seems like it is a ground issue. If the original poster would post his resolution that would help.

But some info on relays and power. And if I wrong it won't be the first time.

The relay should supply the positive 12V DC power. To whatever. The ground or negative side should go to a frame ground or back to the battery.

Frame grounds are a lot of problems on many many electrical issues on a lot of vehicles. Whether it's a side by side or a 2001 GMC Sierra dash cluster (don't ask) or a 1997 Dodge Dakota dash cluster (ground point under the kick panel on driver and passenger side).

Cleaning the ground points or running a ground wire back to the battery should resolve the issue. If the fuel pump and relay is good.  

But usually there are many circuits feeding off one ground point. So it would be best to follow the ground coming off the fuel pump to make sure the ground point is making good contact to frame. 

The ground wire can be tested with a multi-meter.

1. Set multi-meter to OHMS.

2. Hold one lead of multi-meter to the other lead of multi-meter. The reading should be 0.0 to maybe 0.2. That will be the reference of the meter and also tells you there is little to no resistance between the leads.

3. Now take the negative side of the fuel pump wire to one lead of the multi-meter. and touch the other lead to a UNPAINTED part of the frame. The reading should be the same or maybe 0.1 more than when you touch the leads of the meter together. 

If no reading or a very high reading that would indicate a bad connection to ground somewhere and the ground point would need to be cleaned.

 

Hope this info helps you or someone. I'm not responsible if anything unwanted happens while you're testing.

 

 

JDSmith Rookie

JDSmith

Posted
  • Author
Posted

Well we just got it back running…

it was the fuel relay and ecu. Turns out the new ecu was bad as well. A dealer was able to pull a working one off a new unit and it all worked. 
 

the new issue when you put it in reverse it defuels and dies now. The speed sensor is allegedly a common issue, replaced it and same thing. So we just had to leave the speed sensor unplugged and it’s fine. Dealer said Massimo said the causes would be ECU, Speed sensor, or the dash. I’m not replacing the dash so it is just no speedometer for me.

Greg Kilgore Community Regular

Greg Kilgore

Posted
Posted

Glad you got your machine back running. Hopefully the ECU was covered since it was DOA.

I'd guess that since the machine was submerged for a minute or two. There may be more electrical issues pop-up from bad sensors. 

At least the resale value should be higher since your not racking up miles.😁

You may have more relays go in and out or ground issues in the coming future. 

Could an app and cell phone for speed if needed.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • barticus73
      Massimo T-Boss 560 vs CFMoto UForce 600
      By barticus73
      I am looking to buy a small UTV to do work around my property and priced a brand new Massimo T-Boss 560 through Lowes @ $10,500 out the door or a Dealer sold CFMOTO Uforce 600 at $11,500 out the door.    Are there any glaring reasons to go with the Uforce 600 at an extra $1000?  Is one model more reliable than the other?  Any input greatly appreciated.
       
      Thank you,
       
      Jerry
    • Tim n Deb
      2015 Massimo stalled and wont start. oil, new plug, getting gas verified. cranks but does not start
      By Tim n Deb
      Riding out today it acted like it ran out of gas,  stalled and died and would not start.   Towed back to house,  New  plug added this past month,  plenty of oil, getting plenty of gas, battery cranks good.   Trys to kick in and starts but doesnt.   Two days prior while sitting at a idle it died.  Added gas and it started did my ranch chores with it.  But just now it stalled out cranks but will not start.   Tried to find if fault codes came up on the clock like manual says but not sure I am doing that right.  Any and all help apprecated.  Thank you
    • Chile
      Massimo MSU 700 Piston Clearance
      By Chile
      2018 Massimo MSU 700 EFI. I realize that this engine is essential the same as in all of the HISUN based Yamaha clones out there. I am in the process of performing a top end diagnosis/rebuild. I have an AMAZON top end rebuild kit on order in anticipation of this activity. 
      Question 1:  When exploring the myriad of top end rebuild kits on the market for these units there are some cylinder assemblies that have "686 cm3" badging next to the cam cain tensioner boss. Others compatible with the unit do not have this badging. The existing cylinder assy does not have the 686 badging. I am assuming that this simply verifies that the cylinder assy is for a 686 cm3 engine which of course the stock 700 series HISUN engines are. Am I missing something here or is this just a manufacturer artifact? With or without the badging the application listings all indicate compatibility with the MSU 700 series engines.
      Question 2:  I have reviewed at minimum a dozen videos associated with this rebuild. To date I have not found one that deals with piston/cylinder clearance and/or ring gap verification. The advertised specifications for these various "top end rebuild kits" all indicate: Cylnider bore = 102mm and piston diameter=101.5mm. The math yields a .5mm (as in 1/2 mm) difference. That seems to be a very large piston/cylinder clearance.  I realize I am referencing advertised specs rather than emperically measured values but the numbers have gotten my attention.  I have referenced the FSM and found it to be somewhat confusing in this regard. Hopefully the experts on this forum can enlighten me as to where my observations are faulty here.
      Any and all assistance is greatly appreciated .
      Thank you all in advance,
      Chile
    • monkthumper
      2020 Hisun Sector 750 no pwr to fuel pump
      By monkthumper
      Fuel pump is good (i hotwired it) swapped relay with known good one no help. I'm leanin towards ECU but cannot find wiring diagram online. Dont know how fuel pump relay gets its signal, all fuses good, any help? 
    • amiracle40995
      2019 Coleman 550 700-7 code at startup
      By amiracle40995
      I’m getting a 700-7 every startup. I’m having to change the plug every 100 miles on 93 octane gas. I got a lower numbered plug that is supposed to burn hotter. I’m wondering why that comes up every time I start it and if it’s related? I included a picture of the code or whatever it is. I haven’t seen the code in the owners manual or the hisun shop manual I have. 

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...