Quantcast
Jump to content


What has failed or broken  

15 members have voted

  1. 1. What has failed or broken

    • Drive Line
      6
    • Front Shock
      1
    • Rear Shock
      4
    • Differential
      5
    • Ball Joint
      4
    • CV or Axle
      5
    • Computer
      1
    • Electrical System
      6
    • Steering
      2
    • Fuel System problem
      3
    • Oil Problem
      1
    • Engine Trouble
      0
    • Ignition Problem
      0
    • Oil Problem
      1
    • Stock tire failure, not just wore out
      8
    • Power Train Problem
      3
    • Clutch
      1
    • Starter
      4
    • Over Heating
      6
    • Fuses
      8


Recommended Posts

Posted

(1) Drive-line not installed correctly when delivered from Phoenix Not pressed into trans, March 2008

(2) Drive-line taken to shop and repaired, first time taken out the driveline comes apart at the back, the pin and carter pin not installed correctly.April 2008

(3)next day front flat

(4) electrical problem summer 2008, no warning just stopped running

(5) two more flats at same time, unrepairable pin holes in side walls summer 2008

(6)May 2009, drive-line fails

(6) seat latch breaks, seatbelt breaks May 2008

Posted

1. ??? 2nd Ride, right rear CV joint came undone at the wheel

2. 252.9 U joint, replaced with another U joint drive line

3. 691.8 Drive line, replaced with CVs this time, LF Shock, Rear locker

4. ???? Had a hole in the rim caused by a rock wedged between rim and brake caliper. No fault of Joyner

5. 1540 Tube left rear tire\

6. ~1600 Ball joint fell out.

7. 1702 CV joint again, Right rear shock ($149.03)

8. 1742 replaced dust boots on tie rod ends and ball joints, cracked

9. 1991 Fused blown ( by sensor wiring found later)

10. 2069 Fused blown, Found fuse was blown by O2 sensor wiring

11. 2437 Tube Right rear tire

12. 2836 New tires, General AT,

13. 3069 Right rear axle replaced by Joyner, finally after 3 time coming loose

14. 3357 Bolts in read differential failed.

15. 100,000 No more problems, yea, in my dreams :D:lol:

Posted

First ride 10km bolts came loose off of shifter linkage (no 5th gear or reverse)

Same day after fixing shifter linkage cooling fan warped fan blades hitting housing

Second trip 50km front and rear diffs leaking found both grossly overfilled from factory,left rear tire going flat,

same trip noticed right rear shock making noise (spring is rubbing on shock body) have nor replaced yet

third trip last weekend evidnece of engine oil leak , just insatlled joyner cargo rack plastic vibrates like hell

(on the to do list) trailored home in arain storm 4 of 6 headlamps and spot full of water disassembled lights

and siliconed headlamp lenses next trip June 20 ???????

Posted

Left rear tire, pin hole leaks at top of side wall. Leaking from day of delivery.

Rear shocks squeaking after 1st ride, finally replaced with Kings.

Misc. loose bolts.

Rear differential leaks oil at seals after 1st oil change, my fault from overfilling although the front has never leaked.

Top acc. cargo rack rattles like crazy. Repaired it a couple of days ago.

Flat right front tire, rips in side wall, might have been those rocks I hit, now the spare with tube inserted.

Posted
Did you replace just the rears with kings or did you do all 4 ?

I replaced all of them. Area that I ride in is rocky desert terrain and the stock shocks were just too stiff. Even playing with the spring preload and nitrogen pressures they were just too harsh for my bad back.

Posted

The first time out, maybe 10-15 miles. When I got back to the trailer, 3 out of the 4 windshield bolts were missing, and a hex bolt to the rear cage. After that, I stopped at Home Depot and got some lock washers and then went and got 4 things of blue Loc tight. Best $20.00 I ever spent

Guest
This topic is now closed to further replies.
  • Similar Topics

    • By Jeff freeman
      I have a Coleman 550.  Was having problems to start with where it would start and then shut off after a couple tries. It would take off and be good. It then got to a point where it would not start at all. I replaced the fuel injection twice the second time I replaced it I noticed a mouse or something had chewed one of the wires that connect the electrical to the fuel injector. . So two-part question first does anybody have a part number for that wire harness?  Second, any other ideas after I fix the wire harness permanently on what could keep it from starting I have gas flow up to the fuel injector.


    • By Rmillerdesigns
      Hello. I have a 2016 Massimo MSU 500. I was putting on a lightbar and i screwed up and didn't disconnect the battery so when i was taking of the positive cable to put on the power from the lightbar it sparked and now the utv has no power. I turn the key over and all i hear is a chirp. No lights or anything. Everything that comes from the battery to the jumper box up by the battery shows voltage but anything coming out does not such as to the winch or anything like that
    • By GTech
      I have a 2007 Joyner Commando 650, and cannot find a shift cable. Commando is a 4 speed, and the cable I need is the one to the right side of the shifter if you are sitting in the front seat. Cable is approximately 40", and has an eye on each end. I tried fitting a can-am shift cable, and the ends are just too long to mount and make work. Looking for a supplier so I can get the Joyner moving again with the correct shift cable.
      Thank you,
      Gary
    • By mark walkom
      the regen braking on my e1 has stopped working unless (for eg) I am going down a hill in low and it's slowing things down to stick to the 10kph limit. when I drive and take my foot off the accelerator it's not initiating the regen to slow things down and instead just coasts at whatever speed it is at, or speeds up as the regen is not limiting it. the brake lights work, so it's probably not a fault with the sensor on the brake pedal
       
      hoping someone else might be able to provide some suggestions on things to check, as the mob that I bought it off seem to have gone silent on me
    • By J-ree
      hello, I’m new to this website and I joined as sort of a last resort. I bought a China built machine, witch was my first mistake, used it on my Farm for Number of years. Then, I broke it. I spent for ever looking for parts. I can’t find any anywhere! So I came to you. Does anyone out there now where who might have anything that will help. I am open to almost anything. My rear has a straight axle like an old car.  I could change to other styles. All I need is something to work with.  Thanks for listening to me........ Jerry 
×
×
  • Create New...