TROOPER ALIGNMENT / Gumball Crash
-
Similar Topics
-
By Karlibob
I have a 2020 800 sx with about 16 hours on it. From day one I have heard a clunking noise from the front end going over bumps. Has anyone else experienced this? Also this past weekend while out riding I heard a noise that sounded like the dump bed bounced three or four different times, again has anyone experienced anything like that. Thanks, gary
-
By Jon Spruill
Hey Guys, I have been chasing a stalling condition for about two weeks now. The bike will crank up and idle fine, then after about 20 seconds it will fall on its face and stall. It happens at both idle and while running at various rpms. You can turn the key off, turn it back on and it will fire right back up without trouble. I have verified spark on both cylinders with a spark tester. I have also added an inline fuel filter, and pulled the injectors to verify proper pulse on each. Things I have replaced - (relearn procedure performed after each component replaced): spark plugs, ECU, relay/fuse box, fuel pump, & throttle position sensor - all with no improvement of the condition. The only warning light I get when the condition occurs is the oil lamp. The bike only has 14 miles. I am at a loss and appreciate any help and suggestions! Thanks
-
By Blair
Most of us complain about the ridiculous noise in the cabin. My wife likes to ride but the noise is a major downer. You can’t even have a conversation without shouting at each other. Well, I manage to reduce the cabin noise by approx 200%!
I addressed the intake that is poorly placed right between the driver and passenger. First, I cut the air filter inlet pipe in half (pic 1). I then reinstalled it upside down (pic 2). I then attached a flexible intake tube (pic 3) and directed it behind the cabin (pic 4). Major difference.
Then I covered the interior engine cover with Dynamat extreme and then 200 mil Chaogang sound deadener / heat shield mat on top of that (pic 5). Since I cut off the intake and redirected it, I completely closed off the intake (engine fence) so no engine noise can come thru (pic 6). It also reduced the heat approx 50%. I did leave on the heat mat that came stock on the engine cover, so it has 3 different mats. It was a snug fit. Major difference again.
My wife rides all the time now since we can have a conversation when we ride. Major improvement to my riding experience. Thought you might like to check it out.
-
By Robbie Wyre
I'm working on a 2005 Cub Cadet side by side and I'm trying to remove the front two axles. I have a slide hammer puller on the inner joint and with all my strength they will not budge. Anyone have the same issues and is there something I'm missing or a trick of some sort to pull these out? Any suggestions please and thank you.
-
By SpaceGhost
As with any forum you join, there is a requirement for an obligatory introduction... and that seems fair. How else do you get that first post in there without jumping in with some stupid question right out of nowhere?
Hi. I'm Space Ghost. Well, not really, but that was my call sign on my last deployment before an IED made me non-deployable, and I an now retired/disabled, and living on my wonderful VA disability. I did almost 28 years in total between the Army, Army Reserve, and National Guard. 1 deployment with the Reserve (Desert Storm) and 3 with the Guard (1 pre, and 2 post 9/11)
Married (going on 30 years) one of each. (both out of the nest)
My vehicle is (at least not yet) not a UTV, however, it is an ATV, A 2001 Kawasaki Prairie 400.
BTW, That's Brandy, my former PTS/TBI service dog on the bike. RIP old girl. She's internet famous. Perhaps you've seen her before...
The reason I'm here is that Arthritis is starting to set into my wounds and my mobility is getting worse. I will be selling the quad bike soon, and going with a SXS, and have selected a Can Am model as the replacement, so I figured I had better get on board a forum somewhere. Just put in for my Guard retirement, and will be very soon looking to get into a Commander 6x6.
Wouldn't mind having the Limited with the Hvac system, but am really not sure it's worth the extra 10 grand or not. Plus it's 500 pounds heavier, and I prefer the doors off in nice weather. It's so much easier when working in the yard, and so much more fun when on the trail.
Anyway, I'm here now, so it will help me research more and make up my mind. Plus once I have it, I'll be able to share stories about it and of course, continue to learn more, as it will be my 1st sxs. Still have time before I get my retirement. Takes a good 90 days at least according to the guy I talked to... Typical government efficiency... lol.
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.