Quantcast
Jump to content


Recommended Posts

  • 4 weeks later...
Posted

Glad to hear you are up & running. I traced a short or bad ground in my headlights back to the fuse box by the passengers feet. Need to remember to blow it out with air once in awhile. It was full of dirt. If it get wet, that means mud, that means short.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By staind
      Looking for information on installing a OBD port or a lite to read codes in ECM. 
      I can not find a OBD port or a lite to read codes on this R2 with 800cc. 
      I have code readers and adapters for most ATV's. From what I've found so far. They don't have a connection for to read codes. I may be wrong. That's why I'm asking. 
      This R2 has had new IAC, TPS, MAP, fuel pressure regulator and fuel pump replaced. This was done by neighbor to try to stop surging. It still surges on start up and then settles down. But once you hit the accelerator it revs up to 2000+ rpm and stays till you block off IAC port in throttle body with finger. Once you do that it once again settles down and idles perfectly.
      I want to know what the ECM is reading to help dio it.
      This joyner is the first one I've run across. Well second one in a week. (my neighbors 2 of them) The other was a trooper with the 1100cc chery motor that had been setting for years. After cleaning up the fuse box connections. It runs like a top. Had to replace all gages with aftermarket gages. Water, oil, gas, amp. Only problem one was the water temp using original sending unit. Had to install 150 ohm resistor on the input wire to get it to read correctly + - 5 degrees. Close enough. Gas sending unit was/is for a boat tank 6" tall. All SS so it should last forever. 
      thanks Dan D. aka staind
    • By GaryC
      Unfortunately my rear Diff housing cracked on my 2013 and I need to replace it or find a good used complete differential.  I think the same one was used from 2013-2016?  Any help or referrals appreciated.  Thanks, Gary  (949)370-2575 (in UT)
    • By Cletus
      I have a 2016 550, ive tryed the hisun website and seems i cant get parts there. I would like to add power steering, have seen a few "kits" on ebay
      for the 750 not sure if its the same parts needed for the 550, there is a factory bracket already welded to the frame above the standard steering rack, is this to be used
      to mount the eps motor? There is also a grey plug hanging just above the brake master cylinder, not sure if thats anything that needs to be used in the install.
      Handy with wrenches so if i can find the parts installing it shouldnt be a problem, anyone done this upgrade, was it worth it?
    • By Alien10
      I have a Coleman Outfitter 550 purchased in January 2022 that runs and operates pretty well.  65 hours on it so far.   It is a work vehicle for my 10 hilly acres with two 1 acre woods and 5 acres of "lawn".  The rest is under a lake. 
      My parking brake does not seem to have any grip.  It worked when new but after a month or so, it is just almost useless.     I press the parking brake pedal hard until it stops. Still, it won't hold even on slight inclines.   I don't see the caliper move as I press the brake pedal down.  There seems to be plenty of pad left on it and the rotor is shiny as if it is rubbing a little when applied, but not enough to stop it from rolling. 
      Any thoughts on possible causes? 
       
×
×
  • Create New...