Quantcast
Jump to content

Joyner T2 steering boots

fettman1176

By fettman1176
in Joyner UTV SxS Forum

 Share

Recommended Posts

  • 10 months later...
  • 4 weeks later...
  • 7 months later...
Neil Wilson Contributor

Neil Wilson

Posted
Posted
On 12/28/2020 at 8:11 PM, mixfixdave said:

I found some steering rack and pinion boots that work for the Trooper 1100!
Post up if you are looking.

These boots were a life saver for me. Thanks so much for sharing. I had a problem with the Joyner boot clamps not holding the boots on. They would slide off the steering box. To fix it I added some strips of leather under the clamp straps to make them tighter. So far it is working.

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • A P
      2022 Hisun Sector 550 eps. Power steering not working
      By A P
      Hi
      I have a 2022 hisun sector eps 550. 30amp fuse is blown for eps. Checked the motor and it’s fine. Opened up the controller and found a bad diode. Dealer wanted 500$ for the controller. Just posting this in case it helps someone. I couldn’t read numbers from the old one so just took a guess and replaced it with a 100v 3amp diode. 
    • Stan Morton
      2018 Sidekick starter needs replacement ~ Looking for an alternative starter
      By Stan Morton
      My 2018 XG-850-SL starter died yesterday. The old part number from Kubota is E7153-11732 which has been superceed by part # EG881-63010. I am looking for an aftermarket starter because the Kubota retail price for the starter starts at $550 and upwards toward $850.  If anyone has gone down this road before and has found an aftermarket starter ~ please share with me. We own a ranch and this thing is used every single day and is sorely missed when it is down for maintenance.  Kind Regards, ~ Stan
    • matthejl
      2010 Massimo HS500 (carb model) Help
      By matthejl
      Quick history:
      Bought it about a month ago and when I test drove it, it ran good. Loaded it up and took it home. Owner said it had been sitting for a long time, but was "just serviced". It only has 500 miles on it total. Drove it around and found out the charging system wasnt working...so had to charge the battery once every week and a half or so. One day my daughter was driving it and it died. I couldnt get it to start again and I noticed there was no fuel in the filter...I first checked pulse/vacuum line to make sure it was sucking and it was. So I replaced the fuel pump with one I found local...which is for a large riding lawn mower...and it worked. Engine started and ran, but struggled at low speed immediately following running it at higher speed. It would bog when decelerating. I have also noticed now that it will backfire some on decell and die.
       
      In the meantime, I went ahead and installed new stator and trigger coil assembly to get the charging system working again (that was an issue because it would not start at all after that...but eventually found that the trigger coil was wired backwards in the plug from the factory). I have also set valves, but I set them to .005 (intake) and .007 (exhaust)...per the manual. But what is weird is the manual states its mainly for the 700 series, but "can" be used on other models. On the front it says 500/600/700. I have noticed that the most common setting seems to be .005.
       
      Anyways it still has the issue to me that seems like its running lean. Not full power now, struggles immediately running it faster, and will die and pop some on deceleration.
       
      My main problem now is that it wont get to higher rpms as fast as it did when I first bought it. It struggles on deceleration after running near top speed.
       
      Things I have done:
      changed fuel pump
      replaced stator / pickup coil
      thoroughly cleaned carb (twice)
      set valves to .005 and .007 (is .007 too loose for exhaust?)
       
      anyways it seems to have a lean problem, and wondering if you have any suggestions on what to check.
       
      Thanks
    • Brandon Orr
      Joyner 650 axles
      By Brandon Orr
      Does anyone know where I can get rear axles for 09 joyner 650
    • Get More For Your Device
    • CYJSP2009
      Joyner parts
      By CYJSP2009
      Dear Joyner owners
      Any one who is looking for below Joyner parts please send email to casey from Leaf Asia  ( please send to [email protected] and cc to casey2leafasia.biz & [email protected])
      Currently, we have supply below parts: 
      1.  cv axles, cv rebuild kits, cv boots
      2.  Differentials and differential ring and pinion set
      3. Cables, 
      4. Brake parts
      5. Engine parts
      6. Other parts. 
      We will provide better price, close follow up ... 
      We can arrange productioni for parts that we can collect demands from customers  
      Have a good weekend
      Casey /  Leaf Asia 
      2023-11-17
       

  • Gallery Images

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...