-
Similar Topics
-
By Kidsskipp
Getting my prowler to a running stage and can't figure out why it won't idle without throttle. Also see fuel spitting out air intake while running. High speed runs rough as well. I've done many things (that were needed) but it hasn't helped. New plug, rings (120 lbs compression luke warm), timing chain, valve job. Even tried a cheap new carb. Thinking I may be off a tooth on the timing but it looks pretty dang close. anyone see this issue before?
-
By Jacob E freeman
I have a 2018 cub cadet challenger 750 I bought brand new almost 2 years ago the first month I had it the exhaust broke and burnt the spark plug wire in two that was a recall so the dealership installed the new one it had a different design and it bolted up to the bottom two plugs below the spark plug the dealership said they had to Adjust the exhaust valves I get the machine back thanking everything is good now wrong not even a week after I get it back the timing chain tensioner comes apart inside the motor I take it back to the dealership They put one on I get the machine back thanking everything is good but then just like before not even a week goes by when I was riding the Machine automatically quits going come to find out the wet clutch was burned up the primary clutch head stripped off of the splines I get that fixed and then it overheats I take it back they bleed the air out of the coolant they bring it back to me the same day that I get it back it overheats again I take it back they temporarily fix it again just enough to let the warranty run out and now the machine has been to multiple different mechanics I have had them try to bleed the air out they have stood it up on its end I have had the water pump changed I have had the fan hooked to a switch so I could leave it on all the time but still almost 2 years later not even 200 hours on the machine and I cannot ride it The dealership will not take it back as a lemon I have tried I am at my wits end I have no clue what to try next
-
.thumb.jpg.080f7ba3deabf170051987f7b5514b04.jpg)
By RickinMT
2021 Hisun/Axis 700.
I've had some good trail rides with this thing, on some rough roads, although the last two rides weren't rough at all. ANYWAY, yesterday I pulled out of the garage and it clunked really loud, like the clunk when it's trying to pop out of gear... (I think we've all heard that..) And I'm used to it, in both Hi and Lo, but it seemed louder this time but it still moved. I got it up to the front yard and it clunked a few more times, loudly, and then it refused to move. Engine is fine: just no movement. I towed it back down to the garage and took a look at it today. I suspected the belt and had loosened all the belt cover bolts, but I thought I'd check for movement of the drive shaft. Started it up, set the brake, put it in Lo and gunned it. No-go. Then I noticed the front drive shaft was turning a bit. I pushed the button and put it in 4-wheel and gunned it again and the machine lurched forward a bit. The front drive shaft is turning and it wants to move so I guess it's not the belt. SO SO glad I didn't take the cover off- It's a royal pain to put back on... SO. I'm no mechanic but looking for input from you guys. Any suggestions on what to check next? Thanks in advance. So, searching forums.... The symptoms match what some guys are calling a broken "through shaft." I'm seeing drive shaft, through shaft, middle shaft... What to look for? -
By GQStone
We have a 2019 Arctic cat Havoc that has never had the fuel filter changed. It is bogging down and will not reach higher speeds. Has old gas in it and I am sure it needs a fuel filter as well. Can anyone tell me how or where to find parts for this machine? And also where on the machine it is located? I know some are in the tank? Would like to order one but need a starting point or part number.
Thanks in advance.
-
By TomW
I was driving the UTV the other day when it simply died. I was using the sprayer which might have drained the 3 year old battery and the stator didn't recharge it. I towed it to my shop and charged the battery . The next morning it cranked first time and I drove it home . I parked it and turned it off . I then tried to crank it and it would only make a weak click noise . I changed the battery and the voltage regulator but it would still only click. I noticed on the digital display that the reverse light was illuminated and would stay illuminated no matter what gear I selected . If I put it in low that light would light but the reverse light stayed on . Same thing for neutral . I shorted the two poles on the starter solenoid with the key on and it cranked up easily and idled fine. You could put it in reverse and it would move backwards and you could put it in low and it would drive forward. The entire time the reverse light stayed on . I checked the fuses and they all looked good . So lets say I get a new started solenoid . If I replace it and it now starts with the key what is the issue with the reverse light . Is it harmful? What else needs to be done to correct ? Any ideas out there.
-
-
-
Gallery Images
.jpg.e3ec8b63cbe832be6ada8483cf70da21.jpg)
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.