Quantcast
Jump to content


Recommended Posts

Posted

all depends on the problem

Only if you have problems after it sits for a week or so.

if you run it for a hour or so a day like mine, no problems.

 Star Tron also does very well at preventing carbs from gumming etc.  I've cleaned too many carbs where the Sta Bil apparently fell out of suspension and gets sucked into the carburetor all at once.. doesn't run too well on only stabil.

 

 

 

  • Like 1
  • 11 months later...
Posted
On 8/31/2021 at 7:17 PM, Travis said:

all depends on the problem

Only if you have problems after it sits for a week or so.

if you run it for a hour or so a day like mine, no problems.

 Star Tron also does very well at preventing carbs from gumming etc.  I've cleaned too many carbs where the Sta Bil apparently fell out of suspension and gets sucked into the carburetor all at once.. doesn't run too well on only stabil.

 

 

 

Almost a yr later but I never buy Non-ethanol. But I do use Star-Tron. Your gas will NOT go bad if you add Star-Tron....unless you get water and water never did workload with gas. My portable generator has 2 yr old gas in it......with Star-Tron.  Started it a few weeks ago, ran it for half an hr, ran great.

  • Like 2
Posted
2 hours ago, Don W said:

Almost a yr later but I never buy Non-ethanol. But I do use Star-Tron. Your gas will NOT go bad if you add Star-Tron....unless you get water and water never did workload with gas. My portable generator has 2 yr old gas in it......with Star-Tron.  Started it a few weeks ago, ran it for half an hr, ran great.

good to hear!

 

  • 1 year later...
  • 3 weeks later...
  • 2 years later...
Posted
On 8/31/2021 at 2:17 PM, WhiteLightning said:

It's all I use. Only thing I put in my mowers, too.

You’re lucky you have a station that sells it nearby. In AZ tiara aren’t any stations that sell it within 60 miles of Phenix.

  • Like 1
Posted
10 hours ago, Fritz GSD said:

You’re lucky you have a station that sells it nearby. In AZ tiara aren’t any stations that sell it within 60 miles of Phenix.

Lucky for you, AZ has little humidity and lots of sun!

Moisture is the root of the problems that stem from ethanol fuel.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By AlphaSerenity
      Hello,
      Before I invest $10k+ into a brand new UTV for the farm, I want to get my feet wet with a fixer upper and learn the mechanical side of things. I acquired a 2022 Hisun Axis 500 (Lowes-specific model) from an auction for $500. It has only 200 hours and 120 miles on the engine. It looks like the previous owner used it for ranch work and didn't drive it on trails, deep water/mud, or anything too crazy.
      While it runs and moves, it has some problems. It struggles to accelerate up any incline in high and low range and sometimes stalls when I let off of the throttle or change gears. When I apply throttle in neutral, it sounds like it is struggling for fuel/air and pops. When I decelerate, there is a grinding sound coming from the clutch, which I've read to be related to the one way bearing and is semi-common. The last thing I've observed is sometimes the speedometer display sometimes will show a much higher value for a few seconds after barely touching the throttle. Based on the documentation, if a problem is detected from the sensors, the instrument panel display should have an error code rendered on the screen in place of the time, but this isn't happening. Here is a video showing some of these issues (engine is exposed with console removed):
      https://www.youtube.com/watch?v=FFAkO5TaGps
       
      Here is another video of the clutches in action:
       
      I've done some research, but information on this specific unit and sister units is limited. There does seem to be transmission and clutch issues reported. I still need to check into the head gaskets. I don't have the equipment to test compression right now, but I do plan on ordering what is needed soon. I do have an order in place for some cables to read the diagnostics from the computer. There is a shop two hours away from me that works on Hisun products, but I am hoping the problem can be identified and is something within my ability to handle. Below is what I've already investigated.  I am leaning towards the primary clutch needing replacement right now.
      After getting it home and unloaded, I did the following maintenance/checks to it prior to operating it further:
      Changed the engine/clutch oil (and filter) and gear oils using manufacture recommended viscosity Changed the air filter and checked for cracks in the air intake flow. Verified good suction. Cleaned the throttle body Changed the spark plug and verified the gap was within spec (0.6-0.7mm) Changed the coil and coil wire Changed the fuel lines, fuel injector, and verified the fuel pump was outputting the correct initial prime pressure for ignition and continuous pressure after ignition. Also completely emptied the fuel tank and made sure octane 91+ fuel is being used per manufacturer specs. Ran seafoam through system too. Cleaned the spark arrester and verified no cracks or gaps in the exhaust flow Changed out the O2 sensor Checked all wired connections to ensure they were secured and no breaks were visible Checked the belt for tightness and for any signs of wear and tear Verified 4WD and the differential lock function as expected - still hesitates and struggles uphill Verified the fan gears in the shifter are not corroded and working as expected ECU was reset after replacing sensors and fuel-related parts  
       
      Thanks!
    • By Silent3923
      Been waiting over a month and a half for a transmission from bobcat,  they claim the polaris transmission is different.   Can anyone verify that???
    • By OBL
      program will open in old Bud program only/ but will not go in BUDS 2 to let use program ECU problem working on has new engine/ new fuel pump/ injectors/ lines/ sensors/ crank sensor maps/ and new throttle body and injectors. machine starts runs a minute dies/ on 3 rd  try says key not recognized /we put other key in and same thing happens/wait 10 minutes, you can go again/ is there a back door in the program/ also might mention unplug temp sensor and map sensor , it will run a few minutes longer / then die again.
    • By Eman85
      I have been searching and can't find much info on these units. Pretty surprising as every other thing I own I find a lot of info on. Researching for tech info and such it's like no one owns any of these yet I see them everywhere. 
    • By Jeff freeman
      I have a Coleman 550.  Was having problems to start with where it would start and then shut off after a couple tries. It would take off and be good. It then got to a point where it would not start at all. I replaced the fuel injection twice the second time I replaced it I noticed a mouse or something had chewed one of the wires that connect the electrical to the fuel injector. . So two-part question first does anybody have a part number for that wire harness?  Second, any other ideas after I fix the wire harness permanently on what could keep it from starting I have gas flow up to the fuel injector.


×
×
  • Create New...