Quantcast
Jump to content


2022 Massimo T-Boss 410 won't go into drive

Linda Martin

By Linda Martin
in Massimo UTV SxS Forum

 Share

Recommended Posts

  • Alex changed the title to 2022 Massimo T-Boss 410 won't go into drive
T-boss 410 Experienced

T-boss 410

Posted
Posted

Are you stepping on the brake pedal hard enough? I know, sounds kinda stupid, but mine was doing the same thing. It was out of adjustment enough to not turn on the brake lights. Took a  minor adjustment, and it's all good now. 

Joe Breaux Mentor

Joe Breaux

Posted
Posted
On 1/30/2022 at 11:51 AM, Linda Martin said:

My UTV starts but won't go into drive.  Just received the UTV, 2022 t boss 410. Any suggestions 

Return it to store for refund ... buy a Honda.. I wish I had............ My MSU 500 broke on 1st day after 1 mile ... They refused warranty coverage. ever since . I have been bleeding money keeping it running for 3 years now . Been in shop 6 times 

Joe Breaux Mentor

Joe Breaux

Posted
Posted

no,  its actually doing fine . But its now MASSIMO /YAMAHA  hybrid....lol  .. and I carry a toolbox and a towrope in the bed .  With the money I spent in repairs , i could have bought the Honda Pioneer and had money left over. ..  I just wish I had known just how bad Massimo lack of warranty service really is.. BEFORE I bought it from Tractor Supply .  If they would at least back up their product, it would have been OK.. But they dont back up sh&t.. NOTHING!!! Shops wont touch these anymore. They dont get paid.  Its awful.  but I digress...lolol

Joe Breaux Mentor

Joe Breaux

Posted
Posted

great might be a bit overreach.. lets call it adequate, or maybe good. ..... lol  It does run well now and always did well in mud and muck.. But the first two years were .just..... ride for an hour, load on trailer ,bring to shop.. PAY $$$$$  , repeat... repeat, repeat ,repeat...  It got really frustrating . I warn everyone to avoid Massimo. Unless you are a UTV mechanic and can make repairs yourself , or you just have lots of $$$ and like a challenge. lol

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Popular Now

  • Similar Topics

    • AaronD1982
      Massimo Buck 400S UTV Stator......?
      By AaronD1982
      Next problem with charging system to tackle, any help would be appreciated.
      New starter solenoid....check
      New Voltage Regulator...check.
      Dynamic test to Stator.....bang...pulling like 2 Volts AC
      Problem: Without pulling the part out and stranding the vehicle at the shop forever.... I am trying to find the correct stator or at least one that might not be exact for the Massimo Buck 400S, but fit and connect and do the job if that makes sense.... if anyone has any ideas, please shoot them my way.
    • rdc
      Looking for a left rear shaft carrier (just the carrier) for a 2007 Joyner 1100 sand viper
      By rdc
      Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]
    • AaronD1982
      Massimo 400S Buck UTV Starter solenoid replacement
      By AaronD1982
      I recently purchased a 2019 or 2020 (no manual) Massimo 400S Buck Series UTV.  It ran fine for a couple days but the low battery light was flashing while it drove.  It then died in the field one day and I was able to jump the battery and get it rolling enough to get back to the barn.  It started both times I turned the key for a couple days after and when driven died 10 minutes later in the driveway.  Even after jumping it had no juice, but with the key out of the ignition it kept trying to start, a quick look on the Google machine and it suggested starter solenoid or ignition switch was the culprit.  Fair enough, let's just order a replacement solenoid, right?  No way Jose....the pin connector on the UTV is a 2-pin white plastic connector and the part received is a 4 pin.  How do I swap that and make it work?  Can I even?  Where do I find correct parts in the future?
    • Eman85
      Best place to find info on Hisun or Massimo UTV's
      By Eman85
      I have been searching and can't find much info on these units. Pretty surprising as every other thing I own I find a lot of info on. Researching for tech info and such it's like no one owns any of these yet I see them everywhere. 
    • Jeff freeman
      Utv wont start and broken fuel injection wire
      By Jeff freeman
      I have a Coleman 550.  Was having problems to start with where it would start and then shut off after a couple tries. It would take off and be good. It then got to a point where it would not start at all. I replaced the fuel injection twice the second time I replaced it I noticed a mouse or something had chewed one of the wires that connect the electrical to the fuel injector. . So two-part question first does anybody have a part number for that wire harness?  Second, any other ideas after I fix the wire harness permanently on what could keep it from starting I have gas flow up to the fuel injector.


UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...