Quantcast
Jump to content


Joyner 650cc Utv Rectifier Regulator wiring

West Oz Mark

By West Oz Mark
in Joyner UTV SxS Forum

 Share
Go to solution Solved by bmoody4550,

Recommended Posts

West Oz Mark Newbie

West Oz Mark

Posted
Posted

I have purchased a 650cc Utv that is in good mechanical condition but the Electrical system is a mess and is not my strong suit. I have purchased a new Regulator, coil and Distributer but I am having trouble wiring it all up as some of the wiring has been cut and removed. I have found a wiring diagram on line but is not colour coded.

My first job, of many, is to connect up the Rectifier Regulator. On the wiring diagram it has 3 wires running to the alternator (2 only wires currently as pictured but 3 pin plug) and one wire running to the positive of the coil. 

Can anyone advise what wires goes where please? I assume the red wire from the rectifier will run to the +coil.

Regards Mark 

20220516_105135.jpg

20220516_105145.jpg

20220516_105826.jpg

bmoody4550 Apprentice

bmoody4550

Posted
Posted

I think on my machine I ran into the problem where the color of the wires changed.

I had replaced the regulator as well but was just able to plug it in.  do you not have a connector or just loose wires??

My issue was the connector plug up by the alternator (not on the alternator). The pins were so small they were not making contact anymore within the connector to be able to charge the  battery.

Looks like three wires go to the alternator.  You should be able to check continuity between the alternator and the wires you have at the regulator.

I can take a look when I am home to see if any colors are visible on my machine.

 

 

 

West Oz Mark Newbie

West Oz Mark

Posted
  • Author
Posted
3 hours ago, bmoody4550 said:

I think on my machine I ran into the problem where the color of the wires changed.

I had replaced the regulator as well but was just able to plug it in.  do you not have a connector or just loose wires??

My issue was the connector plug up by the alternator (not on the alternator). The pins were so small they were not making contact anymore within the connector to be able to charge the  battery.

Looks like three wires go to the alternator.  You should be able to check continuity between the alternator and the wires you have at the regulator.

I can take a look when I am home to see if any colors are visible on my machine.

 

 

 

Unfortunately the plug was cut and like you said the wire colours don't match up. I have managed to work out the rest of the wiring but the regulator has got me stumped.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • AaronD1982
      Massimo Buck 400S UTV Stator......?
      By AaronD1982
      Next problem with charging system to tackle, any help would be appreciated.
      New starter solenoid....check
      New Voltage Regulator...check.
      Dynamic test to Stator.....bang...pulling like 2 Volts AC
      Problem: Without pulling the part out and stranding the vehicle at the shop forever.... I am trying to find the correct stator or at least one that might not be exact for the Massimo Buck 400S, but fit and connect and do the job if that makes sense.... if anyone has any ideas, please shoot them my way.
    • MilSurpYinzer
      New Mexico etc
      By MilSurpYinzer
      I heard there's several off road festivals out that way. One or two post apocalyptic, the rest just rev and run. Anyone know a good one that offers camping? Any advice for out of state people like hauling, legality, and where to stay?
      Ideally me and the missus would be down for camping out and setting up shop somewhere nearby. That way we can just wake up, load up, and ride.
    • Mitch13
      Coleman 400 wiring help
      By Mitch13
      2022 Coleman 400 with 13 hours on the engine and the mice got to it. Every wire coming out of the steering column in one cluster has been eaten through. I tried reconnecting matching wire colors to each other and I get the left turn signal and hazards to work, nothing else. If I play around a bit I can get the horn to honk or headlights to come on but only when I connect them to the brown wire. Obviously I don't know what I am doing here. Does anyone have a picture of how these wires are connected when they are under the hood on the drivers side coming from the steering column?
      Gray - seems to carry power
      Brown - left turn signal
      Green with purple stripe - hazards?
      Pink with red stripe - horn?
      Green - head lights?
      Yellow - head lights?
      Yellow with red stripe?
      Blue?
      Dark green?
      There is also a bundle hanging under the hood not connected to anything green with yellow strip, brown and blue?
      Other than that issue, I am about ready to sell this for parts if you interested let me know.
      Thanks
    • AaronD1982
      Massimo 400S Buck UTV Starter solenoid replacement
      By AaronD1982
      I recently purchased a 2019 or 2020 (no manual) Massimo 400S Buck Series UTV.  It ran fine for a couple days but the low battery light was flashing while it drove.  It then died in the field one day and I was able to jump the battery and get it rolling enough to get back to the barn.  It started both times I turned the key for a couple days after and when driven died 10 minutes later in the driveway.  Even after jumping it had no juice, but with the key out of the ignition it kept trying to start, a quick look on the Google machine and it suggested starter solenoid or ignition switch was the culprit.  Fair enough, let's just order a replacement solenoid, right?  No way Jose....the pin connector on the UTV is a 2-pin white plastic connector and the part received is a 4 pin.  How do I swap that and make it work?  Can I even?  Where do I find correct parts in the future?
    • Eman85
      New owner Massimo MSU500
      By Eman85
      I just purchased a Massimo MSU500 and no manual came with it so I have some questions. looking for part #'s and availability of basics like spark plug air and fuel filter. What is the valve adjustment specifications? 
        Is there a fuel drain? It's been sitting, low mileage but I want to drain out the old fuel and put fresh. 

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...