Quantcast
Jump to content


Differential Upgrade Kits are available

Guest Lenny

By Guest Lenny
in Joyner UTV SxS Forum

 Share

Recommended Posts

Guest Lenny

Guest Lenny

Posted
Posted

I finally have the Differential Upgrade Kits done and can start to ship next week. I made up 20 kits and used 2 for myself leaving 18 kits left. The kits can be purchased from me for $90 per kit. You will need 2 kits, one for the rear and one for the front. There is a slight difference so be sure to specify which one you want. I will pay for shipping and insurance, priority mail. It should get to you in aprox 3 days. I don't know if I will be making up more kits. It I will depend on how these go. However, if I do, I will be charging $135 per kit after the initial 18. This got a lot more involved and required a lot of shims than I initially thought. Some shims I have to machine after getting them. You will get an extra snap ring to be used where Joyner chose to omit one. Also you will receive 12 special machined bolts. These will be metric grade 12.9, much stronger then the stock bolts. Each bolt includes a locknut for it's rear side. Full instructions with lots of pictures and a shim placement drawing is in the kit. Even though you will have several shims left over, I felt I needed to provide a complete range of thickness capability for each location.

If you would like a kit(s), PM me and I will give you payment instructions. Payments will be made through PayPal.

Thanks for everyone's patience.

Lenny

2328791330104282158OYauDO_th.jpg

Guest Lenny

Guest Lenny

Posted
Posted
Payment sent.

Thanks, it will go out tomorrow. Thats the last kits except for two I'm holding for Paiute3 and one for Kinarfi. If others ore interested in kits, let me know. If I get enough wanting them, I will make up another batch. They will be $135.00 per kit for the new kits.

Lenny

  • 3 weeks later...
ksimpsy Enthusiast

ksimpsy

Posted
Posted

Just finished the front diff and everything worked perfect. the only difference I found is that I had no groove for the new snap ring. not the biggest deal I just didn't put it in.

thanks again Lenny

Kevin

Guest Lenny

Guest Lenny

Posted
Posted
Just finished the front diff and everything worked perfect. the only difference I found is that I had no groove for the new snap ring. not the biggest deal I just didn't put it in.

thanks again Lenny

Kevin

They don't all have the groove. I beleive that there are 3 different versions of the diffs. For the most part they are idenical but there are some suttle changes. Glad it worked good for you. Did your big ring gear bolts show signs beginning to shear? So far everyone I have seen, does. Some of the diffs are unbeleiveably loose in stock form. And, thanks for the good input on my supercharger project.

Lenny

ksimpsy Enthusiast

ksimpsy

Posted
Posted

yeah just finished the rear diff and all the bolts were loose 4 were half sheared off and one was completely broke the dummy that safety wired the thing did it backwards :angry: . its a good thing I didn't go on that last ride. one thing on the rear diff is that I took out all the shims between the cone and bearing and when reassembled it still needs to come down to fit the pinion gear better. so what you said about machiening the shoulder down is a possibility. mine wasn't that bad so i just set it as best i could.

Kevin

Guest Lenny

Guest Lenny

Posted
Posted
yeah just finished the rear diff and all the bolts were loose 4 were half sheared off and one was completely broke the dummy that safety wired the thing did it backwards :angry: . its a good thing I didn't go on that last ride. one thing on the rear diff is that I took out all the shims between the cone and bearing and when reassembled it still needs to come down to fit the pinion gear better. so what you said about machiening the shoulder down is a possibility. mine wasn't that bad so i just set it as best i could.

Kevin

I'm just amazed that everybodys diffs aren't falling apart left an right.

Lenny

  • 2 months later...
  • 2 weeks later...
Guest Lenny

Guest Lenny

Posted
Posted
Got any more of these kits. My front end was grinding a little so I might as well upgrade if I am going to open it up.

Sorry, but I don't. I do understand hat Joyner has decided to warranty any differentials that go bad. You may want to consult joyner or your dealer.

Lenny

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Tim n Deb
      2015 Massimo stalled and wont start. oil, new plug, getting gas verified. cranks but does not start
      By Tim n Deb
      Riding out today it acted like it ran out of gas,  stalled and died and would not start.   Towed back to house,  New  plug added this past month,  plenty of oil, getting plenty of gas, battery cranks good.   Trys to kick in and starts but doesnt.   Two days prior while sitting at a idle it died.  Added gas and it started did my ranch chores with it.  But just now it stalled out cranks but will not start.   Tried to find if fault codes came up on the clock like manual says but not sure I am doing that right.  Any and all help apprecated.  Thank you
    • CSM_Retired
      Kioti K9 Power Dump Kit
      By CSM_Retired
      Has anyone installed the power dump on a Kioti K9? If so, does it eliminate the safety lock? Does it work well?
      Thanks for your input
    • KWinTX
      Information on 2024 Hison 550x Stryker with a No start Issue
      By KWinTX
      I just bought a new 2024 Hison 550 Stryker 2 months ago. this is the second time I have had this issue.  It only has about 20 hours on it. The last time it happened we took it back to the dealer. it was a fuse.  Since we live three-hour time driving there and back. I would like to find another solution if possible.  I have tried all the fuses that seem to have anything to do with starting.  Currently checking the battery. The battery is new. it came with the unit. It is probably 6 months old.  the UTV has all power to everything electrical. lights turn signals and radio all work.  When trying the key to start . it is 100% dead. as in it doesn't even click.  There is a low whirring like the fuel pump is turning on though. The Unit was running and driving just fine.  we shut it down for the night. The next morning my wife found it in this condition.  Thanks for any Ideas or solutions???   Otherwise, it goes back to the dealer tomorrow. Just hope I didn't buy a lemon. Great little UTV when it does run.😅  anyone else ever have this Issue..? 
    • Hunterman22
      2021 Hisun Axis 500 No Start - Need Help Please
      By Hunterman22
      2021 Hisun Axis 500 UTV (From Lowes)
      Will NOT START
      MY apologies if this is to much info just wanted to give yal the most information possible for help.
      I'm a so called diyer. An Electrician by trade 21yrs. I got my S×S from my last job. The contractor purchased this S×S for this specific job brand new, from Lowes. They used it for hauling materials, tools, & a little bit of anything you can think of on an Industrial type job site. 
      I remember getting on the SxS one time & pushed the gas petal all the way to the floor & SxS had very little power. 
      So anyway ,when the job finished up back mid July this year (7/2024) , I asked the contractor what they was going to do with it. I was told to take it. Otherwise it would go to the contractors yard (storage yard) & most likely rust away. 
      Took it home washed it , it had a heavy coat of dust on it & in it dust was every where. My helper & I had to push it on the trailer to get it home.  After washing it throughly I let it sit & dry out for a good day and half, maybe 2 days. Before trying to start it. NO START. Will turn over & try to start but thats it. 
      So here's what I've purchased & installed. New Air Filter, new spark plug, new air idle control valve (AICV), new throttle position sensor, new throttle body, new oxygen sensor, new digital dash speedometer/fuel gauge/clock. 
      Also drained the old oil & gas & replaced with new oil & 93oct. gas. I should probably mention that I've changed the AICV twice. The 1st time I changed the AICV I was able to get the SxS started & let idle for at least 10-15min. Drove out of the garage, with very little power,  turned it around & barely got it back in the garage.That was the one & only time I've been able to start the SxS. I've also cleaned the Throttle Body and & intake with TB cleaner.  So after that the AICV was  making weird noise so I pulled it out & tried cleaning it, pretty sure I messed it up. So I purchased a Throttle Body that came with new AICV & TPS. Still NO START.  I've checked the fuel pump & the fuel injector.  I took the injector off still hooked up to wiring & turned the key over, the injector sprayed a lot of gas out kinda the size of a volleyball. I've also checked the clearance gap on the intake & exhaust valve. But today 11/2/2024 I'm going recheck spark plug gap & the valve gaps. And alot of other checking. Would the driver side seat belt have anything to do with it not starting?? I know the driver side seat belt has to be in gauged for full throttle "going fast". Thing is the drv. side seat belt will latch but feels like might be messed up inside of it. Tired opening it up but to no avail.  I've never had a S×S or 4wheeler so I was really excited when I got the S×S,not so much anymore.  I work on & fix my own vehicles usually no problems.  But this SxS is kicking my ass.
      So if possible & someone could help me with some ideas or tell me what Im doing wrong or did wrong, I would greatly appreciate it.  Thank you for reading thus far.
       
       
    • Some random dude
      Hisun 700 won’t start due to Break switch
      By Some random dude
      2015 Hisun 700 Utv
      the break pedal seems to not fully throw therefore it won’t engage the switch in order to start. 
      it throws enough to stop the UTV but not enough to engage the switch. 
      I used it this morning, started fine, did some work then shut it off to talk to a neighbour and it wouldn’t start after. I can hear the injectors working but the break pedal doesn’t seem to go all the way down. 

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...