Quantcast
Jump to content

Hisun 750 clicking sound under the seat

Paul409

By Paul409
in Hisun UTV SxS Forum

 Share

Recommended Posts

Paul409 Newbie

Paul409

Posted
Posted

Have a Hisun 750 only 700hrs 21 model. Never had issues went to start it and there's a clicking sound under the seat I'm assuming it's the started relay. I for the life of me cannot find the starter, is there a way to test the relay. 

Thank for any support 

Link to comment
Share on other sites
  • Alex changed the title to Hisun 750 clicking sound under the seat
nods Newbie

nods

Posted
Posted

Dollars to Doughnuts you have a bad starter solenoid. Had to have mine changed at 18 hours!  It is fairly easy to test, use a volt meter and connect the ground (black) lead to a chassis ground point, an unpainted bolt would likely due. Take the positive lead of the meter (red) and connect it to the larger terminal of the solenoid that is NOT connected to the battery. It should read 0 volts. Now turn the key to the crank position and if it just clicks read the voltage. If it still shows 0 volts the relay is toast. If you get battery voltage then the problem is not the relay. (You can check your meter function by testing the battery voltage at the battery terminal.)

Hope that helps you.

Link to comment
Share on other sites
Dale Stansbery Apprentice

Dale Stansbery

Posted
Posted

Nods may be correct, but a weak battery can cause the problem, as well as dirty battery terminals, or a weak or dead charging system. I'd first test the battery voltage and if it's less than 12.6 volts, then check the battery terminals for corrosion/looseness, then charge the battery. Start it and check the output of the charging system for >12.6 volts, ~13v+. If it won't start at this point and you're still getting clicking, you'd need to test the solenoid and circuitry to the solenoid from the switch. 

Link to comment
Share on other sites
  • 2 weeks later...
  • 2 weeks later...
aefron88 Community Regular

aefron88

Posted
Posted

So you tried swapping it?

What is the batt voltage at the battery. What is the voltage between the battery side solenoid terminal and the neg batt post?

If those are the same and over 12.5V that's probably ok.

Have you tried shorting the solenoid terminals to bypass it? Does the starter turn?

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • AlphaSerenity
      Hisun Axis 500 Problems - Hesitation, struggles to go up incline, and low speed regardless of gear range
      By AlphaSerenity
      Hello,
      Before I invest $10k+ into a brand new UTV for the farm, I want to get my feet wet with a fixer upper and learn the mechanical side of things. I acquired a 2022 Hisun Axis 500 (Lowes-specific model) from an auction for $500. It has only 200 hours and 120 miles on the engine. It looks like the previous owner used it for ranch work and didn't drive it on trails, deep water/mud, or anything too crazy.
      While it runs and moves, it has some problems. It struggles to accelerate up any incline in high and low range and sometimes stalls when I let off of the throttle or change gears. When I apply throttle in neutral, it sounds like it is struggling for fuel/air and pops. When I decelerate, there is a grinding sound coming from the clutch, which I've read to be related to the one way bearing and is semi-common. The last thing I've observed is sometimes the speedometer display sometimes will show a much higher value for a few seconds after barely touching the throttle. Based on the documentation, if a problem is detected from the sensors, the instrument panel display should have an error code rendered on the screen in place of the time, but this isn't happening. Here is a video showing some of these issues (engine is exposed with console removed):
      https://www.youtube.com/watch?v=FFAkO5TaGps
       
      Here is another video of the clutches in action:
       
      I've done some research, but information on this specific unit and sister units is limited. There does seem to be transmission and clutch issues reported. I still need to check into the head gaskets. I don't have the equipment to test compression right now, but I do plan on ordering what is needed soon. I do have an order in place for some cables to read the diagnostics from the computer. There is a shop two hours away from me that works on Hisun products, but I am hoping the problem can be identified and is something within my ability to handle. Below is what I've already investigated.  I am leaning towards the primary clutch needing replacement right now.
      After getting it home and unloaded, I did the following maintenance/checks to it prior to operating it further:
      Changed the engine/clutch oil (and filter) and gear oils using manufacture recommended viscosity Changed the air filter and checked for cracks in the air intake flow. Verified good suction. Cleaned the throttle body Changed the spark plug and verified the gap was within spec (0.6-0.7mm) Changed the coil and coil wire Changed the fuel lines, fuel injector, and verified the fuel pump was outputting the correct initial prime pressure for ignition and continuous pressure after ignition. Also completely emptied the fuel tank and made sure octane 91+ fuel is being used per manufacturer specs. Ran seafoam through system too. Cleaned the spark arrester and verified no cracks or gaps in the exhaust flow Changed out the O2 sensor Checked all wired connections to ensure they were secured and no breaks were visible Checked the belt for tightness and for any signs of wear and tear Verified 4WD and the differential lock function as expected - still hesitates and struggles uphill Verified the fan gears in the shifter are not corroded and working as expected ECU was reset after replacing sensors and fuel-related parts  
       
      Thanks!
    • MOTORHEAD1959
      Coleman Powersports Youth 125cc ATV won't start
      By MOTORHEAD1959
      ATV just clicks when trying to start. Battery is good, has a new starter, and all the wiring looks good. any suggestions on where to go from here? thanks 
    • nods
      2022 sector 750 GAS powered: Codes E-113, E-108, E-123, E-132, E-650. What are these?
      By nods
      Less than 40 miles can barely start. Dealer is working with Hisun on a number of other issues on this UTV. Can not get clear info on the meaning of these E codes this is getting. Anybody have some clear info for me?
    • malenurse13
      American Landmaster TW450 Won't Start!!
      By malenurse13
      We just bought a used 2017 American Landmaster TW450. No hour meter that I can find, so not sure exactly how much it has been used. 
      The first 2 days we had it, the starter was a little sketchy, but it started after 2-3 tries. Sometimes when turning the key, we would hear a loud metal "clink" sound. Like the starter made contact, but didn't have enough power to turn. 
      THIS MORNING... Turning the key, we hear a single click sound. That's it. Even with a new battery, the starter is still doing the same thing. Both batteries (old and new) were reading 12.8 volts on volt meter. So I'm wondering what else could be going on? Any ideas on what to look for would be greatly appreciated...
      Thank you!
    • Hugh
      2018 Hisun Sector Crew 1000 engine die after about 15 minutes run
      By Hugh
      My 2018 Hisun sector crew engine cut off after about 15 minutes run. There is no indicator of what is wrong, no error code just die and won't restart until it cool down. I notice that the fan is not running but the temp indicator is on low temp, no overheat indicator. I checked the radiator fluid, it is cool to touch.
      Cooling fans are working, I can hear it running once awhile if I can get the engine warm up enough.  Thank you for all the help.
       
      Hugh

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...